342 products were found matching your search for arduino in 1 shops:

The automotive interface is now on your Arduino MKR too! In the automotive sector, the CAN bus enables intelligent or autonomous vehicles and drones to be networked with various industrial sensors and motors.Controller: Microchip MCP2515Transceiver: NXP TJA1049Compatible with all MKR boardsInput voltage either 5 V via the header connector or 7 to 24 V via threaded terminal ends.

The Arduino MKR1010 is a powerful board and the affordable entry point for the development of IoT projects. Communicate via WLAN with the router or via Bluetooth with your smartphone, this board makes your projects flexible and accessible!Connections• 21 digital I/O - interfaces (13 of them with PWM)• 7 analog inputs• 1 analog output• micro USB portTechnical data• SAMD21 Cortex-M0+ 32bit low power ARM MCU• Operating voltage: 3.3 V• Input voltage: 5 V• 48 MHz - crystal oscillator• DC 7 mA (I/O)• Flash Memory: 256 KByte• SRAM : 32 KByte• integrated Li-Po charging circuit• SAMD21 Cortex-M0+ 32bit Low-Power-ARM-MCU• NINA-W10 series from U-BLOX, Low Power 2.4 GHz IEEE® 802.11b/g/n WLAN, Bluetooth v4.2 BLE/EDR• ECC508 Crypto-Authentication

Very sensitive module with 2 outputs.AO - analog input, real-time output voltage signal of the microphone.DO - digital output depends on the volume and the set limit.Specifications• voltage: 3.3 to 5 VDC• outputs: 1x analog + 1x digital• mounting: 1 mounting hole (3 mm)• 2 LEDs: 1x power supply LED + 1x comparator output LED• frequency range: 50 Hz ... 20 KHz• Impedance: 2.2 KOhm• Sensitivity: 48 - 66 dB• Operating temperature: -40 ... +85 °C• Dimensions (L x W x H): 44 x 15 x 10 mm

The Embedded Pi can act as a bridge between the Raspberry Pi and the Arduino™ Shields, but can also be used as a Cortex-M3 evaluation board in stand-alone operation.• 3-way platform for Raspberry Pi, Arduino and the 32-bit Arm Cortex microcontroller• Helps get the maximum from all 3 platformsIncluded:• Embedded Pi board• 4 plastic spacers• 26- and 10-pin flat ribbon cable

A microcontroller board based on the SAM3X8E ARM Cortex-M3 from Atmel. This is the first Arduino™ board with a 32-bit microcontroller.This board contains all the key features to ensure you can start programming quickly and easily.Unlike other Arduino™ boards, the board runs on a power supply of only 3.3 V.This board features:• 54 digital I/O interfaces (12 of which can be used as PWM output)• 12 analogue inputs• 4 UARTs• 84 MHz clock• USB OTG• 2 D/A converters• SPI header• Power supply• JTAG header• Reset/erase buttonTechnical data:• SAM3X8E ARM Cortex-M3 • Operating voltage: 3.3 V• Digital inputs/outputs: 54• Analogue inputs: 12

Arduino™ 9 Axes Motion ShieldThe Arduino™ 9 Axes Motion Shield has been developed with Bosch using their BN0055 absolute orientation sensor as an on-board key feature. With the shield, designers can start to introduce motion sensing to projects, connecting to TinkerKit modules and Arduino™ boards such as Uno, Yun, Leonardo, Ethernet, Mega, Due and Zero Pro.The shield is powered only when connected to an Arduino™ board.Features• BN0055 absolute orientation sensor• 5 V operating voltage• 50 mW power consumption

DescriptionThis is a simple to use PIR motion sensor with Grove compatible interface. Simply connect it to Stem shield and program it, when anyone moves in its detecting range, the sensor outputs HIGH on its SIG pin.The detecting range and response speed can be adjusted by 2 potentiometers soldered on its circuit board, The response speed is from 0.3s - 25s, and max 6 meters of detecting range.Specification• Grove compatible interface• Voltage range: 3 ... 5 V• 2.0cm x 4.0cm twig module• Detecting angle: 120 degree• Detecting distance: max 6m (3m by default)• Adjustable detecting distance and holding timeApplication Ideas• Motion sensor• Thief-guarding System• Switch• Industrial automationFor all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

The Nano is a particularly small Arduino™, which was developed especially for working with plug-in boards. The pins, which are led out via pin headers and the practical size fit on almost all common connector systems. This makes it even easier to try out new ideas and projects.Despite its compact design, the Nano's range of functions almost corresponds to that of a Arduino™ Uno. This is mainly due to the powerful microcontroller of type ATmega328, which has already proven itself on several Arduino™ boards. Via the mini-USB socket you can supply power to the board and circuitry as well as transfer new programs to the controller. Arduino™ Nano 3.xTechnical data:Microcontroller: ATmega328Flash memory: 32 KB SRAM: 2 KBEEPROM: 1 KB Clock rate: 16 MHz I/O pins: 14-of which PWM: 6 -of which analog inputs: 8Connection: Mini-USB LEDs: RXD, TXD, Power, Pin 13, Size: approx. 1.85 cm x 4.3 cmOperating voltage: 5 VRecommended input voltage: 7-12 VMaximum input voltage: 20 VMaximum current per I/O pin: 40 mALoad capacity of the 3.3 V output: 50 mA

Arduino UNO WiFi Rev2With the Arduino Uno WiFi you make your devices WLAN-enabled. This is an Arduino Uno Rev3 with more power: It has a brand new 8-bit microprocessor from Microchip and an integrated IMU (Inertial Measurement Unit). The new ECC608 cryptochip accelerator ensures a secure WLAN connection.14 digital input/output pins (6 of which can be used as PWM outputs)6 analog inputs16 MHz ceramic resonatorUSB portICSP connectorreset buttondimensions: 68 x 53 mm

Arduino UNO mini is a 27 x 34 mm microcontroller board with an ATmega328P microcontroller.This board has• 14 digital I/O - interfaces (6 of them can be used as PWM output)• 6 analog inputs• 16 MHz - crystal oscillator• USB-C connector• resetTechnical databulletpoint# ATMega 328P• Operating voltage: 5 V• Input voltage: 7 ... 12 V• input voltage ( limit ): 6 ... 20 V• digital inputs/outputs: 14• analog inputs: 6• I DC 40 mA (I/O) / 50 mA (3.3 V)• flash memory: 32 KBytebulletpoint# SRAM : 2 KBytebulletpoint# EEPROM: 1 KByte• Clock: 16 MHz Software can be found athttps://www.arduino.cc/en/Main/Software

The Nano Motor Carrier is the perfect add-on for the Nano 33 IoT board as it extends and powers its functionality.The Nano Motor Carrier is designed to simplify motor control. It takes care of the electronics needed to control the motors, allowing students to focus on prototyping and developing their projects. A series of 3-pin headers can also be used to connect other actuators and sensors. The board has a 9-axis accelerometer, gyroscope, and magnetometer on the board. It also includes a battery charger for single-cell Li-ion batteries.To use the Carrier, simply connect it to a Nano 33 board and connect the motors you need for your project. Once it's connected, plug the USB cable into the Nano 33 IoT. Download the Arduino Motor Carrier library from the library manager and you're ready to start programming and controlling your motors using the motor drivers.NoteIf you are working with motors, you will need an external power source to power the motor drivers and run the motors. Battery connection possible or use an external power source.

Perfect for your next IoT projectsCreate projects based on the Arduino Nano board with secure connections via screw terminals. If you need to add additional components, you can use the prototyping area.Fast, safe and ready for additional prototyping.• Fast and secure connection: screw terminals, perfect for solderless and reliable connections for your next IoT project.• prototyping area in place: 8 x 9 plated-through prototyping area for additional components• double row of headers: one row is left empty on each side of the board, with additional quick connections via jumpers• thin headers: lower overall thickness (total thickness including the nano board is less than 15 mm)Specifications• Nano Screw Terminal Adapters (Pack of 3)• screw terminals: 32 screw terminal connectors (3.5 mm pitch)• terminal sockets: 2 double row sockets with 15 contacts each (pitch 2.54 mm)• prototyping area: 9 x 8 grid (2.54 mm)• dimensions (L x W): 70 x 50.5 mm

ARDUINO™ UNO - OPEN SOURCE prototype platformA microcontroller board based on the ATMega328P from Atmel.This board contains all the important features you need to start programming quickly and easily.This board has:• 14 digital I/O interfaces (6 of which can be used as PWM output)• 6 analog inputs• 16 MHz crystal oscillator• USB port• power connector• ICSP header• Reset• DIP/DIL variantTechnical data:• ATMega 328• Operating voltage: 5 V• Input voltage: 7 ... 12 V• Input voltage ( limit ): 6 ... 20 V• digital inputs/outputs: 14• analog inputs: 6• I DC 40 mA (I/O) / 50 mA (3.3 V)• flash memory: 32 KByte• SRAM : 2 KByte• EEPROM: 1 KByte• Clock: 16 MHz Software can be found at:https://www.arduino.cc/en/Main/Software

The Arduino™ Starter Kit!This kit takes you through the basics of using Arduino™ and guides you through 15 interesting projects.Start with the basics of electronics and quickly progress to more complex projects. This kit will help you control the physical world with sensors and actuators.Projects from the kit:• Get to know your tools:Brief introduction to the concept• Spaceship Interface:Design for your control unit• Love-O-Meter:Measure how hot-blooded you are• Color Mixing Lamp:Produce any color with a lamp that uses light as inputContents1x Arduino™ project book , 170 pages1x Arduino™ Uno board Rev31x display1x USB cable1x plug-in board1x mounting base1x 9V battery cliparound 225 components including resistors, diodes, small DC motor, tilt sensor, LEDs, switches and much moreSystem requirements• USB port• Windows XP or better• Mac OS X 10.5 or better• Linux• supported languages: englishPlease noteNot suitable for children under 8 years!

Arduino™ Ethernet Shield 2 without PoEThe Arduino™ Ethernet Shield 2 allows an Arduino™ board to connect to the Internet as well as read and write on a microSD card.The shield is simply mounted on an Arduino™ board, for example on the Arduino™ Uno or since this version also on the Arduino™ Mega. Other shields can be stacked right on top of the Ethernet shield, allowing for optimum functionality integration in designs.Connect the shield to your computer or a network hub/router via a standard Ethernet cable.Features:• W5500 Ethernet chip• Slot for microSD card/card reader• Reset controller• RJ45 Ethernet jack• 5 status LEDs• Dimensions: 6.86 x 5.33 cm

ARDUINO™ UNO open-source prototyping platformA microcontroller board based on the ATMega328 from Atmel.This board contains all the key features to ensure you can start programming quickly and easily.This board features:• 14 digital I/O interfaces (6 of which can be used as PWM output)• 6 analogue inputs• 16 MHz crystal oscillator• USB port• Power supply• ICSP header• ResetTechnical data:• ATMega328• Operating voltage: 5 V• Input voltage: 7 - 12 V• Input voltage (limit): 6 - 20 V• Digital inputs/outputs: 14• Analogue inputs: 6• DC current 40 mA (I/O)/50 mA (3.3 V)• Flash memory: 32 KB• SRAM: 2 KB• EEPROM: 1 KB• Clock speed: 16 MHz The following data is available in the download area:• EAGLE file, Rev. 3, Arduino™ Uno• Arduino™ PDF file (schematic)

Leonardo is Arduino's™ first development board for use of a microcontroller with integrated USB. The ATmega32U4 microcontroller's direct responsibility for the USB enables access to code libraries that allow the board to emulate a computer keyboard, mouse or other device that uses the USB HID protocol.It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analogue inputs), a 16-MHz crystal oscillator, a micro USB connection, a power connector, an ICSP header and a reset button. It contains everything you need to accompany the microcontroller: simply connect it to a computer via a USB cable or power it with an AC/DC adapter or battery, and you'll be ready to go.• ATmega32U4 microcontroller• Input voltage: 7 - 12 V• 20 digital input/output pins• 7 PWM channels• 12 ADCs• 16 MHzPlease also take advantage of our service package, available in the download area.

The Arduino™ motor shield is based on the L298, enabling the user to control inductive loads such as relays, solenoids, DC motors and stepper motors.You can use the Arduino™ shield to control 2 DC motors or 1 stepper motor independently of each other. You can also measure each motor's power consumption and perform many other functions.Technical dataOperating voltage: 5 - 12 VMotor control: L298P, controls 2 DC motors or 1 stepper motorPower: 2 A per channel or max. 4 A (with external power supply)Current detection: 1.65 V/AFree-running stop and brake function

The Portenta Cat. M1/NB IoT GNSS Shield brings cellular communication and positioning to the Portenta H7 boards. The Shield uses a Cinterion TX62 radio module designed for high-efficiency, low-power IoT applications and optimized bandwidth and performance.The Shield enables the development of asset tracking and remote monitoring applications (agriculture, smart cities, utilities) combined with the powerful computing power of Portenta H7. This is a Works with Arduino product, developed by Arduino and Thales.• add NB-IoT, CAT.M1 and positioning to Portenta.• change connectivity capabilities without changing the board.• reduce communication bandwidth requirements in IoT applications• low power module• implement a small multiprotocol gateway (H7 WiFi - BT + NB-IoT/CAT.M1)• compatible with MKR boards and Portenta H7Technical data• Cinterion TX62 radio module (see data sheet)• NB-IoT - LTE CAT.M1• 3GPP Rel.14 compliant protocol LTE Cat. M1/NB1/NB2• UMTS BANDS: 1 - 5 / 8 / 12 (17) / 13 / 18 - 20 / 25 - 28 / 66 / 71 / 85• LTE Cat.M1 DL: max. 300 kbps, UL: max. 1.1 Mbps• LTE Cat.NB1 DL: max. 27 kbps, UL: max. 63 kbit/s• LTE Cat.NB2 DL: max. 124 kbps, UL: max. 158 kbps• point-to-point mobile terminated (MT) and mobile originated (MO) text mode• Protocol Data Unit (PDU) mode• GNSS capability (GPS/BeiDou/Galileo/GLONASS)• Embedded IPv4 and IPv6 TCP/IP stack access• Internet services: TCP server/client, UDP client, DNS, Ping, HTTP client, FTP client, MQTT client Secure connection with TLS/DTLS Secure BootPossible application areas• Remote monitoring• industry and agriculture• public utilities• asset tracking• daily life• fleet management of industrial vehicles

Arduino Nano Every - Perfect for everyday use - based on the ATMega4809 microcontroller.This small, robust and powerful board can be programmed with the easy to use Arduino IDE, available offline and online. It can be used in a breadboard with pin headers or as SMD directly on a printed circuit board.Note: This board is supplied with integrated header.