208 products were found matching your search for differential in 2 shops:

The testo 510 differential pressure measuring device means that heating engineers and air conditioning technicians are well equipped: It measures the differential pressure from 0 to 100 hPa and supports you, for example, when checking filters on air conditioning systems or measuring the gas idle and gas flow pressure on heating systems.You can select the following units on the testo 510 differential pressure gauge: Pa, hPa, mbar, mmH2O, mmHg, inH2O, inHg, psi, m/s, fpm. You can also measure the flow in the ventilation duct with an optionally available pitot tube - from 10 to 100 m/s.Exact: For accurate measurements, the differential pressure measurement is temperature and air density compensated.Uncomplicated: Small, handy and easy to operate with only three buttons.Clever: Thanks to magnets on the back of the device you can work hands-free. In poor visibility conditions such as dark surroundings, the illuminated display makes your work easier.Secure: The differential pressure gauge is safely stored in a belt pouch with a clip-on protective cap, and thanks to a hand loop, it is also well secured during measurement.Ready to start: The silicone connection hose is included in the testo 510 set. So you can start your measurement directly.Product benefits:Differential pressure measurement from 0 to 100 hPaMagnets on the back of the device allow hands-free operation10 units for selection, display in Pascal selectable

Differential pressure gauge PCE-MPM 10For gaseous mediaLC displayMeasuring range ±5000 PaFor mobile use11 different pressure units Product benefits:The differential pressure gauge is a small and handy measuring device for determining the differential air pressure. The differential pressure gauge has a measuring range of ±5000 Pa. The differential pressure gauge is connected via two hose connections with a diameter of 8 mm. After switching on, the differential pressure gauge directly displays the differential pressure. The measured value can be displayed in 11 different pressure units. The differential pressure gauge is used, for example, in ventilation and air-conditioning technology or in educational institutions such as technical colleges and universities. In addition to the normal measured value display, the differential pressure gauge can also display the smallest, largest and average measured value. This makes it easier to analyse the measured values. To save battery power, the differential pressure gauge switches off automatically within five minutes.

PCE Instruments PCE-BDP 10 Bluetooth differential pressure gauge With LCD Differential pressure gauge up to ± 2PSI Bluetooth interface Android and iOS app 11 different units Product benefits: The Bluetooth PCE-BDP 10 differential pressure gauge is designed for checking differential pressure quickly and easily. The Bluetooth differential pressure gauge may be used in ventilation and air conditioning equipment to measure the gas flow pressure or the resting pressure with the help of a smartphone.

PCE-P01 manometerDifferential pressure gauges for the measuring range from -140 to +140 mbar, including softwareSimplest possible operationMeasurement of differential pressure or static pressure in 11 selectable units: Mbar, bar, psi, kPa, ...Measuring range from -140 to +140 mbarMin / Max and Average value display directly on the displayHold functionBacklight can be switched on/offFor long-term measurements incl. Power supplyBattery-level indicatorOptional automatic power-off functionZero point adjustment is possible at any timeSoftware can be downloaded free of charge! Product benefits: The PCE-P01 differential pressure meter is a manometer for simple, fast and precise pressure measurements of air or non-explosive gases. Thanks to its design, the differential pressure meter is suitable for use in the measuring range from -140 to +140 mbar and for the complete display of the measurement results (using special software).The differential pressure meter from PCE Instruments measures differential pressure and the relative pressure and can be switched to different units. 11 pressure measurement units can be set: in H2O, psi, mbar, kPa, inHg, mmHg, ozin², ftH2O, cmH2O, kgcm² or bar. At a resolution of 0.1 mbar, the differential pressure meter achieves an accuracy of 0.3%.

The TT-SI 7005 active differential probe allows for high-voltage measurements to be taken safely and accurately between two voltage points, neither of which are earth-related. This probe is designed for a wide range of measurements up to 60 MHz/± 35 V and is compatible with earthed oscilloscopes from all common manufacturers. Power is supplied via the supplied mains adapter.Bandwidth: 60 MHzDivision factor: x1/x5/x10DC accuracy: ±2Maximum input voltages:Differential:±3.5 V (DC + AC peak) @ x1±18 V (DC + AC peak) @ x5±35 V (DC + AC peak) @ x10to earth: 600 Vrms CAT IIISafety standard: IEC1010-031:2015

The PeakTech 5144 is a measuring instrument used to determine pressure differences.It has a digital multifunction display with backlight. This high-precision measuring instrument can be used in the installation, diagnosis, repair, maintenance and optimisation of air conditioning, heating and ventilation systems. The USB interface and the supplied software are used to log the measured values over longer periods of time.Product benefits:For measuring static differences and pressure differencesMeasuring range of maximum 200 mBarPressure measurement in 11 selectable units of measurement such as: Bar, mbar, psi kg/cm2, kpa and many moreAuto power-off functionData hold functionMIN, MAX, AVG recording functionIntegrated magnetic holder for hands-free operationUSB interface and PC softwareAccessories: Case, USB interface cable, 4mm and 8mm connection tubes, tube adapter, software for Windows, batteries and instruction manual.

Differential Driver And Receiver PairDescriptionThe SN75179B is a differential driver and receiver pair designed for balanced transmission-line applications and meets TIA/EIA-422-B, TIA/EIA-485-A, and ITU Recommendation V.11. It is designed to improve the performance of full-duplex data communications over long bus lines. The SN75179B driver output provides limiting for both positive and negative currents. The receiver features high input impedance, input hysteresis for increased noise immunity, and input sensitivity of ±200 mV over a common-mode input voltage range of -7 V to 12V. The driver provides thermal shutdown for protection from line fault conditions. Thermal shutdown is designed to occur at a junction temperature of approximately 150°C. The SN75179B is designed to drive current loads of up to 60 mA maximum. The SN75179B is characterized for operation from 0°C to 70°C. Features :• Meets or Exceeds the Requirements of TIA/EIA-422-B, TIA/EIA-485-A, and ITU Recommendation V.11• Bus Voltage Range...-7 V to 12 V• Positive- and Negative-Current Limiting• Driver Output Capability...60 mA Max• Driver Thermal-Shutdown Protection• Receiver Input Impedance...12 k Min• Receiver Input Sensitivity...±200 mV• Receiver Input Hysteresis...50 mV Typ• Operates From Single 5-V Supply• Low Power Requirements

The 26PC SMT (surface mount technology) pressure sensor, the first model in the 20PC SMT pressure sensor range, is a small, cost-effective and high-quality pressure measurement solution for use with PCB boards. Based on the proven reliability and accuracy of the 26PC pressure sensor, the 26PC SMT offers a more compact design and genuine SMT functionality. The smaller size means the sensor requires less space on the PCB board, so you can reduce the size of the PCB board. The 26PC SMT can be used as the first pressure sensor together with other SMT components on the PCB board, thus reducing installation costs and eliminating the need for finishing operations.The sensor is fitted with a Wheatstone bridge, piezo-resistive silicon technology and a ratiometric output. This ensures proven application flexibility, a simple design and simple production.The 26PC SMT pressure sensor has been developed for the medical industry, but can be used in any industry in which a placeable pressure sensor is required.• Guide pins for precise positioning• Small package size (less than half the size of the 26PC) and compact profile• 3.18-mm (0.125-inch) diameter recording feature for use in pick-and-place machines• Maximum peak melting temperature of 260°C (500°F)• Relative, vacuum indicator, differential and wet/wet differential measurement in a single housing• Real wet/wet differential measurement• Proven elastomer connections in the 20PC range• Temperature-compensated• End-point calibration• Sensor consisting of only five components• Elastomer design• Large operating temperature range of -40°C to 85°C (-40°F degrees to 185°F)Technical data:Measurement type: wet/wet differential/relative/vacuum gaugeOutput: analogueSignal processing: not reinforcedPressure range: ±15 psiExcess pressure: 45 psiSupply voltage: 10 V DC typically, 16 V DC max.Temperature-compensated: yesOutput calibration: yesResponse time: 1 ms max.Connection type: straight: 1.88 mm dia.Package type: SMTLinearity: ± 0.50% range typically, ± 1.0% range max.Sensitivity: 6.67 mV typicallyTotal margin: 96 mV min., 100 mV typically, 104 mV max.Zero offset: min. -2 mV, typically 0 mV, max. 2 mVZero offset when temperature changes: ±1.0 mV max.Margin distortion when temperature changes: ± 0.75% range typically, ± 1.5% range max.Repeatability and hysteresis errors: ± 0.15% range typicallyInput impedance: 5.5 kOhm min., 7.5 kOhm typically, 11.5 kOhm max.Output impedance: 1.5 kOhm min., 2.5 kOhm typically, 3.0 kOhm max.Shock: qualification tested to 150 gVibration: MIL-STD-202 method 213 (150 g half-sine 11 ms)Operating temperature: -40 - 85°CHarmonised temperature range: 0 to 50°CMedia compatibility: use limited to media that do not corrode seals made from...

Housing: SO-8

Guarantee: 2 years Colour: Black Fitting Position: Rear

Guarantee: 2 years Inner diameter [mm]: 14 Outer diameter [mm]: 55.6 Weight [kg]: 0.24 Fitting Position: Rear Axle Required quantity: 1 Fitting Position: Left (passenger side)

Guarantee: 2 years Fitting Position: Left (passenger side) Weight [kg]: 2.122 Required quantity: 1 Fitting Position: Rear Axle

Guarantee: 2 years Fitting Position: Front Axle Length [mm]: 151 Height [mm]: 68 Inner diameter [mm]: 15

Guarantee: 2 years Inner diameter [mm]: 14 Weight [kg]: 0.258 Required quantity: 2 Fitting Position: Front Fitting Position: Rear axle left and right Outer diameter [mm]: 53.5 Bearing Type: Rubber-metal Bearing

Guarantee: 2 years Required quantity: 1 Weight [kg]: 0.352 Fitting Position: Rear Axle

SNx5176B, Differential Bus TransceiversDescriptionThe SN65176B and SN75176B differential bus transceivers are designed for bidirectional data communication on multipoint bus transmission lines. They are designed for balanced transmission lines and meet ANSI Standards TIA/EIA-422-B and TIA/EIA-485-A and ITU Recommendations V.11 and X.27. The SN65176B and SN75176B devices combine a 3-state differential line driver and a differential input line receiver, both of which operate from a single 5-V power supply. The driver and receiver have active-high and active-low enables, respectively, that can be connected together externally to function as a direction control. The driver differential outputs and the receiver differential inputs are connected internally to form differential input/output (I/O) bus ports that are designed to offer minimum loading to the bus when the driver is disabled or VCC = 0. These ports feature wide positive and negative common-mode voltage ranges, making the device suitable for party-line applications. The driver is designed for up to 60 mA of sink or source current. The driver features positive and negative current limiting and thermal shutdown for protection from line-fault conditions. Thermal shutdown is designed to occur at a junction temperature of approximately 150°C. The receiver features a minimum input impedance of 12 kO, an input sensitivity of ±200 mV, and a typical input hysteresis of 50 mV.Features• Bidirectional Transceivers• Meet or Exceed the Requirements of ANSI Standards TIA/EIA-422-B and TIA/EIA-485-A and ITU Recommendations V.11 and X.27• Designed for Multipoint Transmission on• Long Bus Lines in Noisy Environments• 3-State Driver and Receiver Outputs• Individual Driver and Receiver Enables• Wide Positive and Negative Input/Output Bus Voltage Ranges• ± 60-mA Max Driver Output Capability• Thermal Shutdown Protection• Driver Positive and Negative Current Limiting• 12-k? Min Receiver Input Impedance• ± 200-mV Receiver Input Sensitivity• 50-mV Typ Receiver Input Hysteresis• Operate From Single 5-V Supply

SNx5176B, Differential Bus TransceiversDescriptionThe SN65176B and SN75176B differential bus transceivers are designed for bidirectional data communication on multipoint bus transmission lines. They are designed for balanced transmission lines and meet ANSI Standards TIA/EIA-422-B and TIA/EIA-485-A and ITU Recommendations V.11 and X.27. The SN65176B and SN75176B devices combine a 3-state differential line driver and a differential input line receiver, both of which operate from a single 5-V power supply. The driver and receiver have active-high and active-low enables, respectively, that can be connected together externally to function as a direction control. The driver differential outputs and the receiver differential inputs are connected internally to form differential input/output (I/O) bus ports that are designed to offer minimum loading to the bus when the driver is disabled or VCC = 0. These ports feature wide positive and negative common-mode voltage ranges, making the device suitable for party-line applications. The driver is designed for up to 60 mA of sink or source current. The driver features positive and negative current limiting and thermal shutdown for protection from line-fault conditions. Thermal shutdown is designed to occur at a junction temperature of approximately 150°C. The receiver features a minimum input impedance of 12 kO, an input sensitivity of ±200 mV, and a typical input hysteresis of 50 mV.Features• Bidirectional Transceivers• Meet or Exceed the Requirements of ANSI Standards TIA/EIA-422-B and TIA/EIA-485-A and ITU Recommendations V.11 and X.27• Designed for Multipoint Transmission on• Long Bus Lines in Noisy Environments• 3-State Driver and Receiver Outputs• Individual Driver and Receiver Enables• Wide Positive and Negative Input/Output Bus Voltage Ranges• ± 60-mA Max Driver Output Capability• Thermal Shutdown Protection• Driver Positive and Negative Current Limiting• 12-k? Min Receiver Input Impedance• ± 200-mV Receiver Input Sensitivity• 50-mV Typ Receiver Input Hysteresis• Operate From Single 5-V Supply

Differential Bus TransceiverDescriptionThe SN65ALS176 and SN75ALS176 series combinea 3-stage differential line driver and a line receiver.line receiver, both of which operate from a single 5V power supply. The driver and receiver feature active-highand active-low enables, which can be externallycan be externally interconnected to act asdirectional control. The differential outputs of the driver andthe differential inputs of the receiver are internally connectedto form a differential input/output bus connection that isdesigned to have a minimum load on the buswhen the driver is disabled or VCC = 0. This connectionhas a large positive and negative commoncommon mode voltage ranges, making the device suitable for partylineapplications.Important featuresmeet or exceed the requirements of TIA/EIA-422-B, TIA/EIA-485-A1 and ITU Recommendations V.11and X.27operate at data rates of up to 35 MbaudDesigned for multipoint transmission on long buslines in noisy environmentslow current consumption: max. 30 mAwide positive and negative input/output bus voltage rangethermal shutdown protectionlimitation of positive and negative drive currenthysteresis at receiver inputinterference-free switch-on and switch-off protectionfail-safe receiver open circuit protection

Differential bus transceiverDescriptionCombine the SN65ALS176 and SN75ALS176 seriesA 3-stage differential line driver and oneLine receivers, both with a single 5V power supply. The driver and receiver have Active HighAnd active-low releases that are externalcan be interconnected externally to be used asDirection control. The differential outputs of the driver andThe differential inputs of the receiver are internally connectedTo form a differential input/output bus connection, theThe is designed to minimize the load on the busIf the driver is disabled or VCC = 0. This portHas a large positive and negative common modeCommon mode voltage ranges, which makes the building block for partylineApplications.Important featuresMeet or exceed the requirements of TIA/EIA-422B, TIA/EIA-485-A1 and ITU recommendations V.11And X.27Operates at data transfer rates up to 35 MbaudDesigned for multipoint transmission on long busesLines in noisy environmentsLow current consumption: Max. 30 mAWide positive and negative input/output bus voltage rangeThermal shutdown protectionLimiting the positive and negative driver currentHysteresis at the receiver inputFault-free switch-on and switch-off protectionReceiver fail-safe when the circuit is open

3V LVDS Single CMOS Differential Line ReceiverDescriptionThe DS90LV018A is a single CMOS differential line receiver designed for applications requiring ultra low power dissipation, low noise and high data rates. The device is designed to support data rates in excess of 400 Mbps (200 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology. The DS90LV018A accepts low voltage (350 mV typical) differential input signals and translates them to 3V CMOS output levels. The receiver also supports open, shorted and terminated (100O) input fail-safe. The receiver output will be HIGH for all fail-safe conditions. The DS90LV018A has a flow through design for easy PCB layout. The DS90LV018A and companion LVDS line driver provide a new alternative to high power PECL/ECL devices for high speed point-to point interface applications.Features• >400 Mbps (200 MHz) Switching Rates• 50 ps Differential Skew (Typical)• 2.5 ns Maximum Propagation Delay• 3.3V Power Supply Design• Flow-Through Pinout• Power Down High Impedance on LVDS Inputs• Low Power Design (18mW @ 3.3V Static)• Interoperable with Existing 5V LVDS Networks• Accepts Small Swing (350 mV Typical) Differential Signal Levels• Supports Open, Short and Terminated Input Fail-Safe• Conforms to ANSI/TIA/EIA-644 Standard• Industrial Temperature Operating Range (-40°C to +85°C)• Available in SOIC Package