233 products were found matching your search for tronic in 2 shops:

Charger for 2 V, 6 V and 12 V lead-acid batteries (acid, gel, AGM)• Max. charging current of 0.6 A (automatic adjustment)• Multi-phase Vu charging characteristic curve, I phase, U1 phase, U2 phase• Software-controlled battery test function and defect detection before the start of the charging process• Automatic battery maintenance mode (battery refreshing after charging)• Trickle charge — the battery can remain permanently connected• Protection against reverse polarity, short-circuit and overcharging

This 3-piece set is specially designed to assist in complete oil change for 9G Tronic transmission 725 on Mercedes Benz. It contains a filling oil adaptor, a draining oil multifunction key, as well as an oil drain plug wrench for filling up, draining off and screw removal /installation.

Automatic charger for 2 V, 6 V and 12 V lead and lead gel batteriesAs soon as the battery's final charge voltage is reached, the electronic controller automatically reduces the charging current. This protects the battery from damage. A charge control and polarity display provide information about the correct operating status. Ideally suited for vehicles, boats, caravans, motorcycles and devices that remain unused for long periods of time. • Incl. battery terminals• Protection against short circuit and reverse polarity• Final charge voltages: 2.3/6.9/13.9 V• Charging current: max. 300 mA

For the automatic gauge control of liquids. Features:• Switching point at any water levels can be freely selected• Remote measurement up to 20 m via two-wire line is possible• For all storage devices made from concrete, plastic or metal• No dangerous mains voltage on the sensor• Robust sensor• Unmanned and unsupervised operation• Very easy and fast assembly, as ready to plug in• LED indicators for power and Rel. OnIncluded with delivery:Control unit with detailed installation anduser manual and water sensorTechnical data at a glance:• Operating voltage: 230 V/50 Hz• Power consumption: max. 1 VA• Output voltage: 230 V/50Hz• Switching power: max. 1000 W• Protection rating: IP 20• Dimensions: 160 x 80 x 60 mmA pipe break, an open cellar window in case of heavy rain or a defective seal:Water can cause so much damage in a short time!But this can be prevented very easily.It is also necessary to monitor the liquid level in wells or containers. The new water level switch WPS 1000 is the solution for this - with the ingress of water or when the pre-specified water level is reached, a relay is triggered and automatically switches on the warning devices, pumps or solenoid valves.The WPS 1000 is suitable for all concrete, plastic or metal storage devices and is quickly installed, since all connections can be plugged in. The switching point for any water levels is freely selectable. The control unit is supported by a robust sensor. By eliminating the moving floating switch, the WPS1000 is completely fault-free. LED lights for power and Rel. On show the current status at aglance.

Lightweight and compact, simple handling, individually adjustable!Time and again, uncontrolled flooding that cannot be responded to quickly enough causes massive damage in technical facilities or basements. Permanent monitoring of the liquid level is also necessary is wells or containers. The new water level switch WPS 3000 is the solution to this - in the case of water ingress or when the predefined water level is reached, a relay is triggered and automatically switches on the warning devices, pumps or solenoid valves. The WPS 3000 is suitable for all concrete, plastic or metal storage devices and is quickly installed, since all connections can be plugged in. The switching point for any water levels is freely selectable. The control unit is supported by a robust sensor. By eliminating the moving floating switch the WPS 3000 is completely fault-free. LED lamps for ''Power'', ''Level'' and ''Rel. On'' show the current status at a glance. With two rotary switches or potentiometers, a pump stopping time can be set from 0 to 10 minutes to prevent the relay permanently switching back and forth in wave-like moving water.· Switching point at any water levels can be freely selected· For all concrete, plastic or metal storage devices· Switching output (Rel.) optionally configurable as NC or NO contact· Remote measurement up to 25 m via two-wire line is possible· No dangerous mains voltage on the sensor· Including robust water sensor (cable length 10 m) and mounting material for housing mounting (screws, dowels)

Universal temperature switch UTS 1000Measuring range UTS 1000: -99 ... +850 °C / supplied PT1000 sensor: -50 ... +150 °CSwitching capacity: max. 2300 W (resistive load)PT1000 adapter included for easy connection to PT1000 sensorsInformative OLED display and extensive setting optionsThe UTS 1000 universal temperature switch detects the current ambient temperature and automatically switches a connected 230 V AC device on and also off again when the temperature reaches specified values. For temperature measurement, the universal temperature switch uses widely available PT1000 sensors. Various PT1000 sensors can be used with the universal temperature switch via an enclosed PT1000 adapter. The universal temperature switch can be used wherever heating or cooling operation must be controlled, e.g.: in central heating systems, air conditioning systems, incubators, for greenhouses, hobby rooms, outdoor saunas, terrariums, as a replacement for defective mechanical thermostats.Scope of delivery:Universal temperature switch UTS 1000PT1000 adapter incl. PT1000 sensor (-50 ... +150 degrees Celsius)Operating instructions German / English

Top hat rail temperature switch HTS 1000The top-hat rail temperature switch HTS 1000 can measure the current temperature in the range from -99 degrees Celsius to +850 degrees Celsius (depending on the sensor used) in various media (air, water, oil, etc.) with the aid of a PT1000 temperature sensor.Based on this measured value, a variety of temperature controls can be realized using 3 different functions (thermometer, cooling and heating). Various consumers (e.g. fan heaters, air conditioning systems, alarm systems, etc.) can be controlled automatically and manually via two integrated, potential-free relays. A clear OLED display provides constant (or time-limited) information about the current temperature, selected function and current switching status of the integrated relays.Application examples:Replacement for defective thermostats in heating systemsReplacement control for air conditioning systemsMonitoring and control of temperatures, e.g. in the production of beers and spirits or Temperature-controlled ventilation in greenhousesFeatures:Min. / max. displayHysteresis (switching accuracy) freely adjustable (0.1°C ... 10°C)Sensor monitoring (short circuit, interruption, A/D converter)Output switches off in case of sensor errorOperation and monitoring-free operationAdjustable: thermometer, cooling, heatingOLED display for current temperature, set function and switching states of the relaysData retention in the event of a power failureAutomatic restart after power failureDimensions (temperature switch): 90 x 72 x 72 mmDimensions (temperature sensor): 50 x 6 mmMounting on TS 35 top-hat rail / DIN mounting railTechnical dataOperating voltage: 230 V/AC, 50 HzPower consumption (stand-by): approx. 0.3 WSwitching capacity (total): max. 3000 W (230 V/AC, 13.0 A) for resistive loads, max. 750 W (230 V/AC, 3.2 A) for inductive loadsOutput (screw terminals): 2 x potential-free relays (changeover contact)Resolution: 0.1°C, 1 sSettings: 0.1°C, 1 sMeasuring range (temperature switch PT 1000): -99°C to +850°CMeasuring range (enclosed temperature sensor PT 1000): -50°C to +150°CAccuracy (temperature value): +/- 0,5%Protection class: IP20Sensor cable: 2 meters (can be extended up to 50 m)Operating temperature: -10 °C to 50 °CScope of delivery:HTS 1000 top-hat rail temperature switchPT1000 temperature sensor (cable length 2 m)Operating instructions German / English

Water detector WD 1000Operating voltage: 230 V ~, 50 HzPower consumption (stand-by): approx. 0.5 WTriggering sensitivity: approx. 100 kOLoudness (alarm): approx. 82 dB (in 1 m distance)Sensor: water sensor (included in package contents)Sensor cable: approx. 3 m (extendable up to 20 m)Dimensions WD 1000: 98 x 59 x 42 mm, without plugDimensions water sensor: 75 x 30 x 8 mmProtection class: IP20A defective dishwasher, a burst water pipe in the basement, heavy rain or flooding - with the new WD 1000 water detector from H-TRONIC, homeowners, tenants and even professional facility managers are on the safe side. Because in the event of unwanted water contact, the smart helper immediately sounds the alarm so that a quick response can be made. As soon as the sensor contacts come into contact with water, the integrated acoustic and optical alarm is activated.Package contentsWater detector WD 1000Water sensor (cable length 3 m)Operating instructions German / English

The TS 1000 thermostat is ideal for all applications requiring temperature control in heating or cooling mode. Its external temperature sensor covers a ranges from -99°C to +850°C.A power consumer can be directly connected to the integrated outlet of the thermostat, which then switches it on at the preset temperature. The device can be used as a stand-alone device, such as for frost protection or with central heating, air-conditioning or incubator equipment, but it can also be used as a replacement for defective mechanical thermostats or digital thermometers.For wall mountingTemperature sensor PT 1000 (not included with delivery)Switching temperature of -99°C to +850°C freely adjustableMin./max. displaySerial interface for reading out the measured data (optional)Unmanned and unsupervised operationSensor short circuits and open circuits are detected immediatelyOutput switches off in the event of a sensor errorAdjustable to heating or coolingLED displays for relay on, heating (red), cooling (yellow)Data retention in the event of a power failureTechnical data:- Operating voltage: 230 V AC- Output voltage: 230 V AC, max. 16 A- Power consumption: approx. 2 VA- Switching power: max. 3,000 W- Measurement input: Pt1000 (2-wire)- Accuracy: - Resolution: 0.1°C- Protection class: IP 20- Ambient temperature of the device: -15°C to +50°C- Dimensions (L x W x H): 160 x 80 x 60 mm

The electronic water level switch WPS 5000 is suitable for automatic level monitoring of conductive liquids in tanks, wells, water tanks or similar (such. as rainwater, tap, fresh water, waste, heating and cooling water at backflow of water, for example, by clogged drains, flooding in through cable break, etc.).For storage of concrete, plastic or metal. The device can be configured as either refill or bank discharge. Here, the liquid level automatically between two water level (min. And max) is maintained. When defined ingress of water or when reaching the previously level object speaks the relay of the WPS 5000 (optionally with digital delay setting) and switches on the built-in socket a connected 230 V consumers.Your benefits:On / Off Switch-off delay adjustable: 1 ... 9,999 seconds (approximately 2.8 hrs.).Freely selectable switching pointRelay NO or NC configurableRemote measuring up to 30m possible via a 2-core cable with sensor (included)Input for water sensor or float switch (parallel connection possible)No mains voltage at the sensorSimple and quick installationOperating and unattended operationDim. (L x W x H): 160 x 80 x 60 mm

Water sensor WS 4010, suitable for WPS 4000The water sensor WS 4010 is suitable in conjunction with the H-TRONIC water level switch WPS 4000 for automatic level monitoring of conductive liquids in containers, wells, basement rooms or similar. The metal sensors made of stainless steel are cast into a robust plastic housing. The measuring sensor with 10 meter long PVC connection cable is only intended for monitoring liquid levels in non-aggressive media.Technical specifications:Design: sensor encapsulated in plastic (for conductive liquids).Special features: The measuring electrodes are chlorine and salt water resistant (stainless steel AISI 316 / V4A)Connection: approx. 10 m PVC cable with open endsDimensions (H x W x D): approx. 74 x 29 x 8 mm

The TSM 1000 temperature regulator in the convenient flush-mounted frame is suitable for space-saving mounting in control cabinets. It can also be integrated into an existing switch. It is ideal for all applications requiring temperature control in heating or cooling mode. An external temperature sensor (PT1000) records measurement ranges of -99°C to +850°C. The devices can be used independently, e.g. as a frost monitor, for central heating, air conditioning, incubator etc., but also serve as a replacement for defective mechanical thermostats or for digital thermometers.Temperature sensor PT 1000 (not included with delivery)Switching temperature of -99°C to +850°C freely adjustableMin. /Max. DisplaySerial interface for reading out the measured data (optional)Unmanned and unsupervised operationSensor short circuits and open circuits are detected immediatelyOutput switches off in the event of a sensor errorAdjustable to heating or coolingLED displays for relay on, heating (red), cooling (yellow)Data retention in the event of a power failureTechnical data:- Operating voltage: 10 - 15 V DC- Energy consumption: approx. 60 mA- Output: potential-free relay Contact 230 V AC/5 A or 30 V DC/5 A- Power consumption: approx. 2 VA- Switching power: max. 1000 W- Measurement input: Pt1000 (2-wire)- Accuracy: - Resolution: 0.1°C- Protection class: IP 20- Ambient temperature: -15°C to +50°C- Dimensions (L/W/H): 101/48/35 mm- Cut-out for front frame: 97/43 mm

Water sensor WS 10 - 10 meter length, suitable for WPS 1000 V2.The water sensor WS 10 is suitable in conjunction with the H-TRONIC water level switch WPS 1000 for automatic level monitoring of conductive liquids in containers, wells, basements and the like. The metal sensors are cast in a plastic housing. This measuring sensor with 10-meter PVC connection cable is intended only for detection of liquids in non-aggressive media.Technical specifications:Design: sensor encapsulated in plastic (for conductive liquids).Special features: The measuring electrodes are chlorine and salt water resistant (stainless steel AISI 316 / V4A)Connection: approx. 10 m PVC cable with open cable ends.Dimensions (H x W x D): approx. 74 x 29 x 8 mmPackage Contents:Water sensor with approx. 10 meter connection cable

Water sensor WS 10 - 10 meter length, suitable for WPS 1000 V1.The water sensor WS 10 is suitable in conjunction with the H-TRONIC water level switch WPS 1000 for automatic level monitoring of conductive liquids in containers, wells, basements and the like. The metal sensors are cast in a plastic housing. This measuring sensor with 10-meter PVC connection cable is intended only for detection of liquids in non-aggressive media.Technical specificationsDesign: sensor encapsulated in plastic (for conductive liquids).Special features: The measuring electrodes are chlorine and salt water resistant (stainless steel AISI 316 / V4A)Connection: approx. 10 m PVC cable with 2.5 mm jack plug.Dimensions (H x W x D): approx. 74 x 29 x 8 mmPackage Contents:Water sensor in plastic with approx. 10 meter connection cable and 2.5 mm jack plug

Rain sensor RS 12Ambient temperature: -20 ... +60 °CDimensions: 65 x 50 x 35 mmWeight rain sensor: 64 gWeight angle: 30 gOperating voltage: 12 V DCCurrent consumption with heating: max. 110 mASwitching output (Out): max. 100 mAProtection class: IP65You want an awning to retract automatically in case of rain? A skylight should be closed automatically in case of precipitation? Here is the solution!The RS 12 rain sensor reacts to rain, snow and hail. With additional control electronics, you can, for example, have a sunshade or awning retract in the event of precipitation, close a skylight or just have the precipitation reported. A heater prevents icing or condensation and ensures functional reliability. The rain sensor is connected to the sensor input of the control electronics via the switching output designed as an open collector. The mounting bracket included in the scope of delivery allows flexible mounting on a flat roof, pitched roof or on the house wall. The following connections are possible, for example:RelayIndicator lamp 12 V DCLED 12 VControl signal for PLCMounting optionsWith the supplied mounting bracket, you can mount the RS 12 on a flat roof, pitched roof or on a wall.Package Contents:Rain sensor45° mounting bracket4 screws M 2.6 x 8 mm

for TS 1000 / TSM 1000 / TS 2100Connection cable approx. 15 cmSuitable temperature sensor PT 1000 with screw thread (2 pieces are needed.) Brass G 1/8, wrench size 13 mm. With brass screw-in thread. You need 2 pieces.Technical data:Dimensions: (L x Ø) 16 x 14 mmConnection wires: approx. 200 mm, G 1/8Wrench width: 13 mm.Temperature range: -40 to +250 degrees Celsius

Water level switch WPS3000 compactThe best of H-Tronics water level switches in one compact deviceFilling and draining conductive liquids, maintaining levels or reporting leaksMaximum switching capacity: 2300 W (resistive load)A compact OLED display provides information on the current statusWould you like to automatically refill your garden pond with fresh water? Do you want to keep the water level in your cistern at a certain level? Or do you want to reliably detect leaking, conductive liquids? Here is the solution! The WPS3000 compact water level switch monitors the level of conductive liquids and combines several functions in one compact device. The water level switch detects changes in the level of conductive liquids, such as water, in a liquid container using attached water sensors. The water level switch controls 230 V AC devices connected via a relay, e.g. a pump or a solenoid valve.Scope of delivery:Water level switch WPS3000 compact2 water sensors 10 m incl. wall mountingsOperating instructions German / English

Are you looking for reliable protection against water damage and the associated high renovation costs? Do you want to provide your washing machine or dishwasher with additional protection? This is the solution. The WSS 1 water fault circuit breaker detects leaks, alerts the user to these with an acoustic and visual signal and switches off the power and water supply. Possible applications include the detection of defects on washing machines, dishwashers or hot water boilers. Flood alarm or additional protection for water level or float switches.Technical dataAmbient temperature: 0 - +50 �°CRelative humidity: Dimensions of WSS 1: 98 x 60 x 41 mmDimensions of WSS 1V: 84 x 54 x 40 mmDimensions of water sensor: 75 x 30 x 8 mmWeight of WSS 1/WSS 1V/water sensor: 157/315/56 gOperating voltage: 230 V ACPower consumption: approx. 5.0 WPower consumption in standby: approx. 0.5 WSwitching capacity (resistive load): max. 3680 WTripping sensitivity: .100 kOhmProtection rating: IP20Water sensor connection: 3.5 mmSolenoid valve connection: 2.5 mmAlarm volume: approx. 80 dBWater connection: G3/4Cable length: approx. 2 m

Inrush current limiter SCL 3680Your powerful angle grinder, a strong compressor or a powerful pump trigger the fuse when switched on? Here is the solution!We are talking about the inrush current, i.e. the electrical current that flows immediately after a powerful device is switched on. It is often many times higher than the rated current and loads the mains and connected consumers equally. This can lead to undesirable effects such as the tripping of fuses and circuit breakers or even the overloading of the entire system. The SCL 3680 inrush current limiter provides a remedy here and briefly reduces the high inrush currents to prevent the fuse from blowing.FunctionThe SCL 3680 inrush current limiter prevents the fuse from tripping unintentionally when powerful loads are switched on. The intermediate plug reduces the load peaks typical of high-consumption devices when they are switched on.FeaturesThe inrush current limiter is suitable for circuits with a fuse rating of 16 A.Technical dataOperating voltage: 230 V ~, 50 HzPower consumption (stand-by): approx. 0.6 WRated current: max. 16 A Rated power: max. 3680 WSuitable for circuits with 16 A fuse protectionAmbient temperature: -10 °C to 50 °CDimensions: 98 x 59 x 41 mm without plug Protection class: IP20Package contents:Inrush current limiter SCL 3680Operating instructions German / English

Solar charge controller, 53 WThis charge controller switches off the charge current automatically when the charging end voltage reaches 13.8 V and switches the solar panel back on when the figure falls below the minimum voltage of 13 V. Two LEDs indicate the following states: charging and battery full. The module is simply switched between solar panel and battery.