1286 products were found matching your search for Fehler Im System Vinyl in 4 shops:

Ready-to-install high performance loudspeaker system for suspended installations features an 8" 50W driver, 70V 32W transformer, 2 cu.ft. acoustic enclosure and white grille. It's ideal for high energy, high ceiling applications like clubs, bars, sporting facilities, concourses, hotel ballrooms, transportation terminals, convention centers and exhibit halls. Driver (8A50) 8" 50W driver features 20 oz. LF magnet with 1.4 inch copper voice coil to drive a polypropylene cone with half-roll rubber surround for long cone travel and good edge damping. Post-mounted tweeter is a 1 inch balanced-drive dome protected by Ferrofluid and a first-order high-pass filter. A steel plate is mounted over the driver to protect it during shipping and installation. Remove it to mount the grille. See the driver spec sheet for more information. Transformer (TLS-3270) Includes 70V 32W transformer for superior music fidelity in 70V distributed applications. The 20/20 AudioVision transformer offers true 20Hz-20kHz performance. A screwdriver-adjustable tap selector switch is accessible through an opening in the grille. Note: Lowell 20/20 AudioVision transformers have full frequency response and high powerhandling which allows the speaker to operate at full potential while providing a stable load to the amplifier. The transformer allows a distributed speaker system to sound imperceptibly the same as a transformer-less direct-to-voice-coil system but with easier wiring, reduced labor and less expense. Grille Square perforated steel grille with white powder epoxy finish is ideal for applications where the speaker is suspended in a tile, sheetrock or plaster ceiling. 15.25" square x 0.375" Enclosure 2 cu.ft. precision-formed steel enclosure (23.94" x 18.19" x 8.19") features anti-vibration ribs, sound-stop board, 1-1/2" thick premium acoustic lining and forged 1/4"-20 eyebolts screwed into mounting nuts for secure suspended installation (using flyware by others). Externally accessible connections are terminated through a 4" x 4" flush cover plate. Black powder epoxy finish.

Under the umbrella of high-performance audio equipment, the IM12P-TS100-3SW Speaker System stands out as a superior choice for suspended installations. This ready-to-install loudspeaker system is designed with a 12" 150W driver, a TLS-10070 70V transformer, and a 3 cubic foot acoustic enclosure, all encased in a stylish white grille. This system is perfectly tailored for high-ceiling, high-energy environments such as clubs and bars, sports facilities, concourses, hotel ballrooms, and exhibit halls. The 12P150 driver, an 8-ohm, 150W component, boasts a robust motor structure, a hefty 38 oz. magnet, and a 2" voice coil. It also features a coaxially mounted high-frequency compression driver, ensuring high power handling with exceptional efficiency. The driver is protected by a steel plate during shipping and installation, which can be removed to mount the grille. The TLS-10070 transformer, a 70V 100W component, ensures superior music fidelity in 70V distributed applications. This transformer, part of the Lowell 20/20 AudioVision series, offers true 20Hz-20kHz performance. The speaker system also includes a screwdriver-adjustable tap selector switch, accessible behind the grille. Lowell's 20/20 AudioVision transformers are known for their full frequency response and high power handling, allowing the speaker to operate at full potential while providing a stable load to the amplifier. The system's square perforated steel grille, finished in white powder epoxy, is ideal for installations where the speaker is suspended in a tile, sheetrock, or plaster ceiling. The 3 cubic foot precision-formed steel enclosure features anti-vibration ribs, a sound-stop board, and a 1-1/2" thick premium acoustic lining. For secure suspended installation, the system includes forged 1/4"-20 eyebolts screwed into mounting nuts. Externally accessible connections are terminated through a 4" x 4" flush cover plate, finished in black powder epoxy. For plenum spaces with limited height, a 2 cubic foot enclosure option is also available. The IM12P-TS100-3SW Speaker System, with its high-quality components and efficient design, is a reliable choice for those seeking superior sound distribution.

For superior audio performance in high-energy environments, consider the IM12Q-TS100-3SW Speaker System. This high-quality, durable speaker system is expertly designed by Lowell Manufacturing, a reputable brand renowned for its top-tier audio equipment. It includes a 12P150 12" 250W driver, a TLS-10070 70V transformer, and a 3 cubic foot square enclosure, making it an efficient and reliable choice for your audio needs.This stylish speaker system is specifically designed for suspended installations, making it an excellent choice for venues with high ceilings such as clubs, bars, sporting facilities, hotel ballrooms, and exhibit halls. The 12" (8 ohm) 250W driver features a robust motor structure with a 77 oz. magnet and a 4-inch edge-wound aluminum voice coil. The 5.3" mylar dome tweeter, with a 42 oz. magnet and 1.75" voice coil, delivers an exceptional combination of power handling and efficiency.The built-in crossover network with fourth-order high-pass and fourth-order low-pass filters ensures proper frequency division between the two drivers. The driver frame is cast in corrosion-resistant black aluminum, with a protective steel plate mounted over it for shipping and installation.The included TLS-10070 70V 100W transformer offers superior music fidelity in 70V distributed applications. Lowell's 20/20 AudioVision transformers provide full frequency response and high power handling, allowing the speaker to operate at full potential while providing a stable load to the amplifier. This results in a distributed speaker system that sounds as good as a transformer-less direct-to-voice-coil system, but with easier wiring, reduced labor, and less expense.The speaker system also features a square perforated steel grille with a white powder epoxy finish, ideal for installations in tile, sheetrock, or plaster ceilings. The 3 cubic foot precision-formed steel enclosure features anti-vibration ribs, a sound-stop board, and a 1-1/2" thick premium acoustic lining. Forged 1/4"-20 eyebolts screwed into mounting nuts ensure secure suspended installation. The enclosure's black powder epoxy finish adds a sleek touch to its design, while externally accessible connections are conveniently terminated through a 4" x 4" flush cover plate. In summary, the IM12Q-TS100-3SW Speaker System is a high-quality, durable, and efficient choice for any high-ceiling, high-energy environment.

You can elevate your audio experience with the IM8P-TS100-2SW Speaker System, a ready-to-install, high-performance loudspeaker system specifically designed for suspended installations. This robust system includes an 8P100 8" 100W driver, a TLS-10070 70V transformer, and a 2 cubic foot square acoustic enclosure, making it an excellent choice for venues requiring high-energy sound distribution, such as clubs, bars, sporting facilities, hotel ballrooms, transportation terminals, and convention centers.The 8P100 8" driver is a high-quality component featuring a robust motor structure, a 38 oz. magnet, and a 2" voice coil. It also includes a coaxially mounted high-frequency compression driver, offering high power handling with exceptional efficiency. To ensure the driver's safety during shipping and installation, it comes with a protective steel plate that can be removed when mounting the grille.The TLS-10070 70V transformer is a key feature of this speaker system, providing superior music fidelity in 70V distributed applications. The transformer is part of Lowell's 20/20 AudioVision series, offering true 20Hz-20kHz performance. A screwdriver-adjustable tap selector switch is conveniently located behind the grille, allowing for easy adjustments.The IM8P-TS100-2SW Speaker System also includes a stylish square perforated steel grille with a white powder epoxy finish. This grille is perfect for installations where the speaker is suspended in a tile, sheetrock, or plaster ceiling. The enclosure is a 2 cu.ft. precision-formed steel structure, featuring anti-vibration ribs, a sound-stop board, and a 1-1/2" thick premium acoustic lining. For secure suspended installation, it comes with forged 1/4"-20 eyebolts screwed into mounting nuts.Externally accessible connections are terminated through a 4" x 4" flush cover plate, and the enclosure is finished with a sleek black powder epoxy. With the IM8P-TS100-2SW Speaker System, you can enjoy reliable, high-quality, and efficient sound distribution in any high-ceiling application.

Just when you thought mounting a standard riflescope on your AR-style rifle couldn't get any easier, the Leupold Mark IMS Integral Mounting System with 35mm Rings emerges as a game-changer. This robust and reliable mounting solution is specifically designed to address the common challenges of scope height and eye relief that AR rifle enthusiasts often encounter.Crafted from high-quality, durable aluminum, the Mark IMS boasts a sturdy cantilever design that directly attaches to the firearm's Mil-Spec 1913/Picatinny rail. This innovative structure not only raises the scope to the optimal height but also pushes it forward, thereby negating the need for additional risers or the compromise of using specialized optics that may limit your field of view.The 35mm rings incorporated into this one-piece mount ensure a secure and reliable hold on your scope, maintaining its stability even under the most demanding conditions. The matte black finish adds a sleek, professional look to your setup while also providing an extra layer of protection against the elements.For long-range shooting aficionados, the Mark IMS Integral Mounting System comes equipped with a 20 MOA slope. This feature is invaluable for extending the effective range of your rifle, allowing for precise bullet drop compensation over greater distances.Versatility is at the heart of the Leupold brand, and this mounting system is no exception. Whether you're engaged in tactical operations or out in the wilderness hunting, the Mark IMS Integral Mounting System delivers unparalleled accuracy and reliability. Its legendary ruggedness and absolute waterproof integrity mean that you can trust this mount in any environment.In summary, the Leupold Mark IMS Integral Mounting System with 35mm Rings for AR Rifles, with its 20 MOA incline and matte black finish, stands as a testament to Leupold's commitment to quality and innovation. It's a top-tier choice for shooters who demand the best in terms of performance, durability, and versatility.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12 Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12 Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

Enhance the look of your entryway, bedroom or storage area with the Countryside styling of this 72 in. sliding door. Constructed using only quality materials, the MDF is wrapped in a vinyl finish with a sturdy metal frame that will provide years of lasting enjoyment. Complete with installation hardware, this system is easy to install even for the novice DIY. Available in a variety sizes and to meet your design needs.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. This 2-in-1 system allows you to cut mat in middle and use both ends of mat. Helping reduce waste with money savings! A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. This 2-in-1 system allows you to cut mat in middle and use both ends of mat. Helping reduce waste with money savings, A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. This 2-in-1 system allows you to cut mat in middle and use both ends of mat. Helping reduce waste with money savings, A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. This 2-in-1 system allows you to cut mat in middle and use both ends of mat. Helping reduce waste with money savings! A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film. Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12-Watt per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.

Modular Garden Fence System is the fast, easy way to install outdoor fencing. No tools or cutting are required and no more ugly chicken wire. Simply glide the stake through the guide holes on the sides of each panel and press it into the ground. That's it. Twelve linear feet of modular fencing is included in each kit. The fact is you can add as many kits as you need to build any size fence. Removing your modular fence is quick and easy. Simply pull up the stakes one at a time and fold each panel in a zig-zag motion. The fence stores flat with the stakes installed. When you want to reuse your fence, simply start at 1 end, unfold your panels and press the stakes back into the ground. You're not limited to squares or rectangles. Make circles, triangles, zig-zag or scalloped shapes if you wish. You can even easily bend individual panels to make custom corners. Color: Green. Material: Vinyl.