57 products were found matching your search for minwax in 1 shops:

Minwax Polycrylic Polyurethane is a crystal clear, ultra fast-drying protective topcoat. Protects and adds beauty to interior wood surfaces including woodwork, furniture, doors and cabinets. Ideal for use over light woods like maple, ash and birch as well as over Minwax water-based wood stains.

Minwax water based Helmsman spar urethane is a crystal clear, water-based finish that is specially formulated to protect wood against nature's toughest conditions.

Minwax Helmsman spar urethane is specially formulated as a protective clear finish for exterior or interior wood exposed to sunlight, water or temperature changes.

Minwax Polycrylic Polyurethane is a crystal clear, ultra fast-drying protective topcoat. Protects and adds beauty to interior wood surfaces including woodwork, furniture, doors and cabinets. Ideal for use over light woods like maple, ash and birch as well as over Minwax water-based wood stains.

Minwax Polycrylic Polyurethane is a crystal clear, ultra fast-drying protective topcoat. Protects and adds beauty to interior wood surfaces including woodwork, furniture, doors and cabinets. Ideal for use over light woods like maple, ash and birch as well as over Minwax water-based wood stains.

Helmsman Spar Urethane is specially formulated as a protective clear finish for exterior or interior wood exposed to sunlight, water, or temperature changes. Ideal for use on doors, windows, trim, bathroom cabinets, bar tops, kitchen countertops, outdoor furniture. Not recommended for floors.

Minwax Gel Stain is a non-drip stain that adds natural colors and accentuates the beauty of a wide range of wood and non-wood surfaces including wood, plywood, veneer, fiberglass, metal and molded fiberboard.

Minwax Gel Stain is a non-drip stain that adds natural colors and accentuates the beauty of a wide range of wood and non-wood surfaces including wood, plywood, veneer, fiberglass, metal and molded fiberboard.

Minwax Gel Stain is a non-drip stain that adds natural colors and accentuates the beauty of a wide range of wood and non-wood surfaces including wood, plywood, veneer, fiberglass, metal and molded fiberboard.

Minwax Tung Oil Finish creates a remarkably durable, hand-rubbed luster in minutes. Resistant to spills and water spotting.

Minwax Polyshades combines stain and polyurethane in one simple step. Each coat provides rich color and lasting protection while enhancing the wood grain. This product will reduce finishing time compared with staining with one product and protecting with another. Polyshades stain and polyurethane also allow you to easily change the color of your currently stained or varnished wood without stripping. Over old varnish, you can change the color without removing the old finish or hiding the grain.

Minwax Polyshades combines stain and polyurethane in one simple step. Each coat provides rich color and lasting protection while enhancing the wood grain. This product will reduce finishing time compared with staining with one product and protecting with another. Polyshades stain and polyurethane also allow you to easily change the color of your currently stained or varnished wood without stripping.

Minwax Polyshades combines stain and polyurethane in one simple step. Each coat provides rich color and lasting protection while enhancing the wood grain. This product will reduce finishing time compared with staining with one product and protecting with another. Polyshades stain and polyurethane also allow you to easily change the color of your currently stained or varnished wood without stripping. Over old varnish, you can change the color without removing the old finish or hiding the grain.

Minwax Polyshades combines stain and polyurethane in one simple step. Each coat provides rich color and lasting protection while enhancing the wood grain. This product will reduce finishing time compared with staining with one product and protecting with another. Polyshades stain and polyurethane also allow you to easily change the color of your currently stained or varnished wood without stripping. Over old varnish, you can change the color without removing the old finish or hiding the grain.

"Minwax PolyShades combines stain and polyurethane in one simple step. Each coat provides rich color and lasting protection while enhancing the wood grain. This product will reduce finishing time compared with staining with one product and protecting with another. PolyShades stain and polyurethane also allows you to easily change the color of your currently stained or varnished wood without stripping. Over old varnish you can change the color without removing the old finish or hiding the grain. For additional protection, without adding color, add a coat of Minwax fast-drying polyurethane or Minwax wipe-on poly. Using a natural bristle brush, dip approximately an inch into the can, gently tapping it against the inside to remove any excess. Apply a very thin, even coat following the direction of the grain. Make sure to maintain a ""Wet"" edge. To minimize the brush marks and bubbles after staining, tip off the surface by holding the brush at a 45 degree angle and lightly run the bristles over the entire length of the wood. Let the first coat dry for 6 hours or more. Dry time may be extended due to high humidity, low temperature and inadequate ventilation or if the coat is applied too thick. Rub the surface lightly with fine steel wool. Remove all dust. Brush on a second thin coat following directions above. To deepen the color, apply a third coat. To help ensure uniform acceptance of stain color and beautiful results, pretreat new or raw wood with oil-based Minwax pre-stain wood conditioner, following label directions."

Protect your wood projects and get more done, faster, with Minwax One Coat polyurethane protective finish. This crystal clear protective top coat dries in just two hours and lets you complete wood projects 3x faster without sacrificing durability. The advanced formulation in this clear top coat provides the same level of durability in one coat the is comparable to three coats of a conventional polyurethane. Use it to easily protect and add beauty to your wood projects. It's non-ambering and also cleans up easily with just soap and warm water. It is available in a variety of sheens. Apply a coat of Minwax One Coat polyurethane with a high-quality synthetic bristle brush. Apply in the direction of the wood grain in one smooth, uniform coat. Special Instructions: Minwax One Coat polyurethane should not be applied over red mahogany stains. Instead use Minwax fast drying polyurethane or Minwax water based oil-modified polyurethane over any red mahogany stain. Special instructions: Minwax One Coat polyurethane is not recommended for use on floors because it would require more frequent recoating in high traffic areas. Instead, we recommend Minwax super fast drying polyurethane for floors or Minwax ultimate floor finish for maximum durability. Surface must be dry and free of wax, grease, polish, old finishes in poor condition or any foreign matter. Sand to a smooth, uniform surface. Do not use steel wool. Remove dust with a damp cloth. Let dry completely. Advanced formulation provides the same level of durability in one coat that is comparable to three coats of a conventional polyurethane.

Minwax Polyshades combines stain and polyurethane in one simple step. Each coat provides rich color and lasting protection while enhancing the wood grain. This product will reduce finishing time compared with staining with one product and protecting with another. Polyshades stain and polyurethane also allow you to easily change the color of your currently stained or varnished wood without stripping. Over old varnish, you can change the color without removing the old finish or hiding the grain.

Minwax antique furniture refinisher removes old finishes, including shellac, lacquer and some early forms of varnish.

Minwax Polyshades combines stain and polyurethane in one simple step. Each coat provides rich color and lasting protection while enhancing the wood grain. This product will reduce finishing time compared with staining with one product and protecting with another. Polyshades stain and polyurethane also allow you to easily change the color of your currently stained or varnished wood without stripping. Over old varnish, you can change the color without removing the old finish or hiding the grain.

Minwax Polyshades combines stain and polyurethane in one simple step. Each coat provides rich color and lasting protection while enhancing the wood grain. This product will reduce finishing time compared with staining with one product and protecting with another. Polyshades stain and polyurethane also allow you to easily change the color of your currently stained or varnished wood without stripping. Over old varnish, you can change the color without removing the old finish or hiding the grain.