107 products were found matching your search for grove in 2 shops:

Connect the Arduino MKR to the large Grove ecosystem.The shield is perfect for rapid prototyping without soldering. Simply connect your sensors directly to this shield with Grove connectors.14x Grove connectionsI²C and UART interfaceThe board offers both Single Grove and Double Grove analogue inputs

DescriptionCompared with the Electronic Brick system, the Grove System uses only 1 type of cable, (the Electronic Brick system uses 4). These cables are compatible with all modules included in the Grove system.• 5 cables are included in this pack.For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

Grove is a man in his own right!

DescriptionGrove - LED String Light is a LED Driver.work voltage of module is 5V/3V3,But String light is working on 12V,so this module is base on AIC1896,which is a current mode step up DC/DC Converter. Grove - LED String Light is equipped a 5M RGB LED String Light,you can use it to dress Christmas tree and light you Party.Specification• 50 RGB LEDs (5 m)• JST 2.0 Interface • Grove Interface • Colorful Package Include• Grove - LED String Light• LED String• Grove cable-20cmFor all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionCompared with the Electronic Brick system, the Grove System uses only 1 type of cable, (the Electronic Brick system uses 4). These cables are compatible with all modules included in the Grove system.• 5 cables are included in this pack.For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionGrove - Universal 4 Pin connector 90° is the white 4-pin buckled connector used on Stem, Twigs and the Grove cables, the pin spacing is 2mm. There are 10 connectors per bag, Users can use them to DIY.For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionCompared with the Electronic Brick system, the Grove System uses only 1 type of cable, (the Electronic Brick system uses 4). These cables are compatible with all modules included in the Grove system.• 5 cables are included in this pack.For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

With these specially designed conversion cables, you can easily integrate the comprehensive Grove system into breadboards or other microcontrollers that do not currently have a compatible Grove Base Shield.- Scope of delivery of this pack: 5 cables.- Length: 20 cmFor the users of Grove (especially beginners) there are instructions in pdf format. Before using the product you should read the chapters ''Preface'', ''Getting Started'' and ''Introduction to Grove''!

DescriptionCustomers who want to use Grove modules directly with an Arduino can get conversion cables 4-pin jumper (coupler) to 4-pin Grove on request. The jumper coupler is compatible with the 2.54 inch male connectors. With this conversion cable all Grove modules from Seeed can be connected to any 2.54 inch connector.Technical data• 'Buckled Connectors' on the Grove side (JST connectors, 2.0 mm)• jumper coupling can be used with 2.54 mm connector strip• length: 30 cmScope of delivery• 5 cables, 30 cm lengthFor Grove users (especially beginners), there are instructions in pdf format. Before using the product, you should definitely read the chapters ''Preface'', ''Getting Started'' and ''Introduction to Grove''!

DescriptionCompared with the Electronic Brick system, the Grove System uses only 1 type of cable, (the Electronic Brick system uses 4). These cables are compatible with all modules included in the Grove system.• 5 cables are included in this pack.For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionThe sensor on Grove - Gesture is PAJ7620U2 that integrates gesture recognition function with general I2C interface into a single chip. It can recognize 9 gestures including move up, move down, move left, move right, etc with a simple swipe of your hand.Following is a video which using Gesture sensor with matrix to display the direction of hand.We can utilize the gesture to adjust the sound volume, control a robot. Or we can make a remote-control unit, which is able to operate many devices at the same time via a gesture sensor. Features• 9 gesture recognition• Built-in proximity detection• Various main boards support: Arduino UNO/Seeeduino/Arduino Mega2560Features• Interface:IIC• 9 gesture recognition• Operating Power:5V• Dimensions:20*20mm• Sensor: PAJ7620U2• Detecting range: 5 - 15cm• Ambient light immunity: • Gesture speed mode: Normal and GamingFor all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionThe Grove - Ultrasonic Sensor is a non-contact distance measurement module compatible with the Grove system. It is designed for simple, modular projects with industrial performance. An electronic version of this module is also available.Technical features• sensor range: 3 cm to 4 m - best results at 30 degree angle.• Grove interface• power supply: 3.3/5 V DC• ready for Arduino LibraryFor Grove users (especially beginners) there are instructions in pdf format. Before using the product, you should definitely read the chapters ''Preface'', ''Getting Started'' and ''Introduction to Grove''!

DescriptionThis module is an incremental encoder. It encodes the rotation angle signal of the axis and transmits the signal in the form of electronic pulses. The Grove - Encoder belongs to the Grove series and has a standard Grove interface. If the project requires a rotary knob, e.g. a volume control for a loudspeaker, a selector switch or a digital input, this product is the first choice!NoteIf it is pressed, it can generate another signal. Due to the limited number of Grove signal cables, there is no output for this signal.Technical features- Incremental encoder- Grove interface.- Rotation angle: 360 degreesTechnical data- Voltage: 4.5 ~ 5.5 V- Current intensity: 10 ~ 30 mA- Dimensions: 20 x 20mmFor the users of Grove (especially beginners) there are instructions in pdf format. Before using the product, you should definitely read the chapters ''Preface'', ''Getting Started'' and ''Introduction to Grove''!Further product information from the manufacturer underhttp://wiki.seeedstudio.com/Grove-Encoder/

DescriptionIt consists one coin type motor which is a Permanent Magnet coreless DC motor. It vibrates when the input is logic HIGH. It is very easy to drive and Grove compatible. Can be used in toys and cell phone modules.For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionThe Grove - Loudness Sensor is designed to detect the loudness of environmental sound. Based on amplifier LM2904 and a built-in microphone, it amplifies and filters the high frequency signal that received from the microphone, and outputs a positive envelop. This will make for Arduino's signal acquisition. The output value depends on the level of sound input. In order to avoid unnecessary signal disturbances, input signal will go through two times filtering inside the module. Lastly, there is a screw potentiometer that enables manual adjustments to the output gain.Features• Grove compatible interface• Wide supply voltage range• Built-in signal filtering• Gain adjustable via screw potentiometerSpecificationsVoltage: 3.5 ... 10 VDCWorking Frequency: 50 ... 20000 HzSensitivity: -48 ... +66 dBSignal-to-noise Ratio: >58 dBOutput Signal Range: Digital Signal (0 - 1023)For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionTheGrove - Moisture Sensor can be used to detect the moisture of soil, to judge if there is dampness around the sensor. It can be used to decide if the plants in a garden need watering. It can be used in gardens to automate watering plants. It can be used very easily by just inserting the sensor into the soil and reading the output using ADC.NoteThis sensor is not hardened against contamination or exposure of the control circuitry to water and may be prone to electrolytic corrosion across the probes , please use it for PROTOTYPING ONLY.Features• Grove compatible interface• Easy to useSpecification• Operating voltage: 3.3~5V• Operating current: 35mA• Sensor Output Value in dry soil: 0~ 300• Sensor Output Value in humid soil: 300~700• Sensor Output Value in water: 700 ~ 950• PCB size: 2.0cm X 6.0cmFor all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionSummer is coming, want to make a UV detector to know the UV index when you are under the sun? Grove - Sunlight Sensor is recommend here.Grove - Sunlight Sensor is a multi-channel digital light sensor, which has the ability to detect UV-light, visible light and infrared light.This device is based on SI1145, a new sensor from SiLabs. The Si1145 is a low-power, reflectance-based, infrared proximity, UV index and ambient light sensor with I2C digital interface and programmable-event interrupt output. This device offers excellent performance under a wide dynamic range and a variety of light sources including direct sunlight.Grove - Sunlight Sensor include an on-bard Grove connector, which help you to connect it your Arduino easily. You can use this device for making some project which need to detect the light, such as a simple UV detector.Features• Digital light sensor• Wide spectrum detection range• Programmable configuration• 3.3/5V Supply• Detect sunlight directly• Grove compatible• I2C Interface(7-bit)Specification • Operating Voltage: 3.0-5.5V• Working current: 3.5mA• Wave length: 280-950nm• Operating Temperature: -45-85oCFor all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionGrove - Temperature Sensor uses a thermistor to measure ambient temperature. The resistance of thermistor changes based on ambient temperature. This resistance value alters the output of a voltage divider which is measured by an analog input pin and converted to a temperature value. The operating range is -40 to 125°C , with an accuracy of 1.5°C .Features• Grove compatible interface• Arduino library readySpecifications• Operating voltage: 3.3~5V• Thermistor Zero power resistance: 100 KO• Resistance Tolerance: ±1%• Thermistor: NCP18WF104F03RC (NTC)• Nominal B-Constant: 4250 ~ 4299K• Operating temperature range: -40°C to 125°C• Accuracy: ± 1.5°CFor all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

DescriptionNear Field Communication (NFC) is a transmission standard for contactless data exchange over short distances. The Grove NFC Shield works with the PN532 Transceiver Module for contactless communication at 13.56MHz and enables e.g. reading and writing of 13.56MHz tags or point-to-point data exchange between two NFC Shields. The Grove NFC uses the communication protocols I²C or UART (default = UART). The new version has an independent PCB antenna that can be led out of the housing used, giving more freedom to design the project.Technical data- Operating voltage: 3.3V- Operating current: Static Mode: 73 mA, Write/Read Mode: 83mA- supported host interfaces: I²C, UART (default). - for contactless communication at 13.56 MHz- supports ISO14443 protocols type A and B- max. distance during operation for NFC tag detection: 28 mm (depending on antenna size) - for point-to-point communication- Dimensions: 25,43mm x 20,35mmScope of delivery- 1x Grove - NFC- 1x NFC antenna- 1x IPX connection cable - 120 mm- 1x 24 AWG Grove cable - 4P-4P-2.0 - 200 mmFor the users of Grove (especially beginners) there are instructions in pdf format. Before using the product, you should definitely read the chapters ''Preface'', ''Getting Started'' and ''Introduction to Grove''!Instructions and program files at: http://wiki.seeedstudio.com/Grove_NFC/

DescriptionLine finder is designed for line following robotic. It consists two parts - an IR emitting LED and an IR sensitive phototransistor. It can output digital signal to a microcontroller so the robot can reliably follow a black line on a white background, or vice versa.Features• Grove compatible interface• Small size• 5V DC power supply• Indicator LED• Digital output• Distance adjustableFor all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.