1560 products were found matching your search for microchip in 1 shops:

DC-DC converter, step-upHousing: SOT-23-6

DC/DC converter, step-downHousing: SOT-23-6

The MCP8025 is a 3-phase brushless motor gate driver and power module that integrates the following features: key-off sleep mode, a LIN transceiver, a buck voltage regulator, two LDO regulators, power monitoring comparators, an over-temperature sensor, a zero-crossing detector, a neutral simulator, a comparator and an operational amplifier for motor current monitoring.The phase comparator and multiplexer allow for hardware commutation detection. The neutral simulator allows commutation detection without a neutral tap in the motor. The buck converter is capable of delivering 750 mW of power for powering a companion microcontroller. The buck regulator may be disabled if not used. The on-board 5-V and 12-V low dropout voltage regulators are capable of delivering 30 mA of current.• Integrated operational amplifier• Over-current comparator with DAC reference• Phase comparator with multiplexer• Neutral simulator• Adjustable output buck regulator (750 mW)• Output voltage range: 6 - 19 V• Buck regulator under-voltage lockout: 4.0 V• Under-voltage lockout (UVLO): 5.5 V• Over-voltage lockout (OVLO): 20 V• Transient (100 ms) voltage tolerance: 48 V Technical data:Operating voltage: 6 - 19 VOutput current: 50 mAMotor control: PWM

High-speed CAN transceiver with VIOHousing: DIP-8

The MIC29150/29300/29500/29750 are high-current, high-accuracy, low-dropout voltage regulators. Using proprietary Super ßeta PNP® process with a PNP pass element, these regulators feature 350mV to 425mV (full load) typical dropout voltages and very low ground current. Designed for high-current loads, these devices also find applications in lower current, extremely low dropout-critical systems, where their tiny dropout voltage and ground current values are important attributes.

High-speed CAN transceiver with VIOHousing: SOIC-8

The MCP2561/2FD is a Microchip Technology Inc. second-generation high-speed CAN transceiver. It offers the same features as the MCP2561/2. In addition, it guarantees loop delay symmetry in order to support the higher data rates required for CAN FD. The maximum propagation delay was improved to support longer bus length. The device meets the automotive requirements for CAN FD bit rates exceeding 5 Mbps, low quiescent current, electromagnetic compatibility (EMC) and electrostatic discharge (ESD). • Implements ISO-11898-2 and ISO-11898-5 standard physical layer requirements• Very low standby current (5 µA, typically)• VIO supply pin to interface directly with CAN controller and microcontroller with 1.8 V - 5.5 V I/O• SPLIT output pin to stabilise common mode in biased split termination schemes • Protection against high-voltage transients in automotive environments• Automatic thermal shutdown protection• Suitable for 12-V and 24-V systems Technical data:Input voltage: 4.5 - 5.5 VSupply current: 5 - 10 mAStandby current: 5 - 15 µALeakage current: -5 - +5 µA

Dual push/pull comparator• 1.8 VHousing: SO-8Manufacturer: Microchip

300 mA, High-Performance LDODescription:The MCP1755/1755S is a family of CMOS low-dropout (LDO) voltage regulators that can deliver up to 300 mA of current while consuming only 68.0 µA of quiescent current (typical). The input operating range is specified from 3.6V to 16.0V, making it an ideal choice for four to six primary cell battery-powered applications, 12V mobile applications and one to three cell Li-Ionpowered applications. The MCP1755/1755S is capable of delivering 300 mA with only 300 mV (typical) of input-to-output voltage differential. The output voltage tolerance of the MCP1755 is typically +0.85% at +25°C and ±2.0% maximum over the operating junction temperature range of -40°C to +125°C. Line regulation is ±0.01% typical at +25°C. Output voltages available for the MCP1755/1755S range from 1.8V to 5.5V. The LDO output is stable when using only 1 µF of output capacitance. Ceramic, tantalum or aluminum electrolytic capacitors may all be used for input and output. Overcurrent limit and overtemperature shutdown provide a robust solution for any application. The MCP1755/1755S family has a true current foldback feature. When the load impedance decreases beyond the MCP1755/1755S load rating, the output current and voltage will gracefully foldback towards 30 mA at about 0V output. When the load impedance increases and returns to the rated load, the MCP1755/1755S will follow the same foldback curve as the device comes out of current foldback. Package options for the MCP1755 include the SOT-23-5, SOT-223-5 and 8-lead 2 x 3 DFN. Package options for the MCP1755S device include the SOT-223-3 and 8-lead 2 x 3 DFN.Features:• High PSRR: >70 dB @ 1 kHz, typical• 68.0 µA Typical Quiescent Current• Input Operating Voltage Range: 3.6V to 16.0V• 300 mA Output Current for all Output Voltages• Low Dropout Voltage, 300 mV typical @ 300 mA• Standard Output Voltage Options (1.8V, 2.5V, 2.8V, 3.0V, 3.3V, 4.0V, 5.0V)• Output Voltage Range 1.8V to 5.5V in 0.1V Increments (tighter increments are also possible per design)• Output Voltage Tolerances of ±2.0% over entire Temperature Range• Stable with Minimum 1.0 µF Output Capacitance• Power Good Output• Shutdown Input• True Current Foldback Protection• Short-Circuit Protection• Overtemperature ProtectionApplications:• Battery-powered Devices• Battery-powered Alarm Circuits• Smoke Detectors• CO2 Detectors• Pagers and Cellular Phones• Smart Battery Packs• Portable Digital Assistant (PDA)• Digital Cameras• Microcontroller Power• Consumer Products• Battery-powered Data Loggers

Dual push/pull comparator• 1.6 VHousing: DIP-8Manufacturer: Microchip

The MIC29150/29300/29500/29750 are high-current, high-accuracy, low-dropout voltage regulators. Using proprietary Super ßeta PNP® process with a PNP pass element, these regulators feature 350mV to 425mV (full load) typical dropout voltages and very low ground current. Designed for high-current loads, these devices also find applications in lower current, extremely low dropout-critical systems, where their tiny dropout voltage and ground current values are important attributes.

Quad push/pull comparator• 1.6 VHousing: DIL-14Manufacturer: Microchip

Quad push/pull comparator• 1.8 VHousing: SOIC-14Manufacturer: Microchip

The MTD6505 is a 3-phase sensorless driver for brushless DC (BLDC). It features a 180-degree sine drive, a high torque and noise-free driving. Motor excess current limitation and over-temperature protection are included for safety.

Dual push/pull comparator• 1.6 VHousing: SO-8Manufacturer: Microchip

300 mA, High-Performance LDODescription:The MCP1755/1755S is a family of CMOS low-dropout (LDO) voltage regulators that can deliver up to 300 mA of current while consuming only 68.0 µA of quiescent current (typical). The input operating range is specified from 3.6V to 16.0V, making it an ideal choice for four to six primary cell battery-powered applications, 12V mobile applications and one to three cell Li-Ionpowered applications. The MCP1755/1755S is capable of delivering 300 mA with only 300 mV (typical) of input-to-output voltage differential. The output voltage tolerance of the MCP1755 is typically +0.85% at +25°C and ±2.0% maximum over the operating junction temperature range of -40°C to +125°C. Line regulation is ±0.01% typical at +25°C. Output voltages available for the MCP1755/1755S range from 1.8V to 5.5V. The LDO output is stable when using only 1 µF of output capacitance. Ceramic, tantalum or aluminum electrolytic capacitors may all be used for input and output. Overcurrent limit and overtemperature shutdown provide a robust solution for any application. The MCP1755/1755S family has a true current foldback feature. When the load impedance decreases beyond the MCP1755/1755S load rating, the output current and voltage will gracefully foldback towards 30 mA at about 0V output. When the load impedance increases and returns to the rated load, the MCP1755/1755S will follow the same foldback curve as the device comes out of current foldback. Package options for the MCP1755 include the SOT-23-5, SOT-223-5 and 8-lead 2 x 3 DFN. Package options for the MCP1755S device include the SOT-223-3 and 8-lead 2 x 3 DFN.Features:• High PSRR: >70 dB @ 1 kHz, typical• 68.0 µA Typical Quiescent Current• Input Operating Voltage Range: 3.6V to 16.0V• 300 mA Output Current for all Output Voltages• Low Dropout Voltage, 300 mV typical @ 300 mA• Standard Output Voltage Options (1.8V, 2.5V, 2.8V, 3.0V, 3.3V, 4.0V, 5.0V)• Output Voltage Range 1.8V to 5.5V in 0.1V Increments (tighter increments are also possible per design)• Output Voltage Tolerances of ±2.0% over entire Temperature Range• Stable with Minimum 1.0 µF Output Capacitance• Power Good Output• Shutdown Input• True Current Foldback Protection• Short-Circuit Protection• Overtemperature ProtectionApplications:• Battery-powered Devices• Battery-powered Alarm Circuits• Smoke Detectors• CO2 Detectors• Pagers and Cellular Phones• Smart Battery Packs• Portable Digital Assistant (PDA)• Digital Cameras• Microcontroller Power• Consumer Products• Battery-powered Data Loggers

The MIC29510 and MIC29512 are high-current, high-accuracy, low-dropout voltage regulators featuring fast transient recovery from input voltage surges and output load current changes. These regulators use a PNP pass element that features proprietary Super ßeta PNP® process.The MIC29510/2 is available in two versions: the 3-pin fixed output MIC29510 and the 5-pin adjustable output voltage MIC29512. All versions are fully protected against overcurrent faults, reversed input polarity, reversed lead insertion, over-temperature operation, and positive and negative transient voltage spikes.A TTL-compatible enable (EN) control pin supports external on/off control. If on/off control is not required, the device may be continuously enabled by connecting EN to IN.The MIC29510/2 is available in the standard 3- and 5-pin TO-220 package with an operating junction temperature range of 0°C to +125°C.For applications requiring even lower dropout voltage, input voltage greater than 16V, or an error flag, see the MIC29500/29501/29502/29503Fast transient response5A current capability700mV dropout voltage at full loadLow ground currentAccurate 1% guaranteed tolerance

300 mA, High-Performance LDODescription:The MCP1755/1755S is a family of CMOS low-dropout (LDO) voltage regulators that can deliver up to 300 mA of current while consuming only 68.0 µA of quiescent current (typical). The input operating range is specified from 3.6V to 16.0V, making it an ideal choice for four to six primary cell battery-powered applications, 12V mobile applications and one to three cell Li-Ionpowered applications. The MCP1755/1755S is capable of delivering 300 mA with only 300 mV (typical) of input-to-output voltage differential. The output voltage tolerance of the MCP1755 is typically +0.85% at +25°C and ±2.0% maximum over the operating junction temperature range of -40°C to +125°C. Line regulation is ±0.01% typical at +25°C. Output voltages available for the MCP1755/1755S range from 1.8V to 5.5V. The LDO output is stable when using only 1 µF of output capacitance. Ceramic, tantalum or aluminum electrolytic capacitors may all be used for input and output. Overcurrent limit and overtemperature shutdown provide a robust solution for any application. The MCP1755/1755S family has a true current foldback feature. When the load impedance decreases beyond the MCP1755/1755S load rating, the output current and voltage will gracefully foldback towards 30 mA at about 0V output. When the load impedance increases and returns to the rated load, the MCP1755/1755S will follow the same foldback curve as the device comes out of current foldback. Package options for the MCP1755 include the SOT-23-5, SOT-223-5 and 8-lead 2 x 3 DFN. Package options for the MCP1755S device include the SOT-223-3 and 8-lead 2 x 3 DFN.Features:• High PSRR: >70 dB @ 1 kHz, typical• 68.0 µA Typical Quiescent Current• Input Operating Voltage Range: 3.6V to 16.0V• 300 mA Output Current for all Output Voltages• Low Dropout Voltage, 300 mV typical @ 300 mA• Standard Output Voltage Options (1.8V, 2.5V, 2.8V, 3.0V, 3.3V, 4.0V, 5.0V)• Output Voltage Range 1.8V to 5.5V in 0.1V Increments (tighter increments are also possible per design)• Output Voltage Tolerances of ±2.0% over entire Temperature Range• Stable with Minimum 1.0 µF Output Capacitance• Power Good Output• Shutdown Input• True Current Foldback Protection• Short-Circuit Protection• Overtemperature ProtectionApplications:• Battery-powered Devices• Battery-powered Alarm Circuits• Smoke Detectors• CO2 Detectors• Pagers and Cellular Phones• Smart Battery Packs• Portable Digital Assistant (PDA)• Digital Cameras• Microcontroller Power• Consumer Products• Battery-powered Data Loggers

12-Bit DAC with SPI™ InterfaceDescription:The MCP492X are 2.7 – 5.5V, low-power, low DNL, 12-Bit Digital-to-Analog Converters (DACs) with optional 2x buffered output and SPI interface. The MCP492X are DACs that provide high accuracy and low noise performance for industrial applications where calibration or compensation of signals (such as temperature, pressure and humidity) are required. The MCP492X are available in the extended temperature range and PDIP, SOIC, MSOP and TSSOP packages. The MCP492X devices utilize a resistive string architecture, with its inherent advantages of low DNL error, low ratio metric temperature coefficient and fast settling time. These devices are specified over the extended temperature range. The MCP492X include doublebuffered inputs, allowing simultaneous updates using the LDAC pin. These devices also incorporate a Power-On Reset (POR) circuit to ensure reliable power-up.Features:• 12-Bit Resolution• ±0.2 LSB DNL (typ)• ±2 LSB INL (typ)• Single or Dual Channel• Rail-to-Rail Output• SPI™ Interface with 20 MHz Clock Support• Simultaneous Latching of the Dual DACs w/LDAC• Fast Settling Time of 4.5 µs• Selectable Unity or 2x Gain Output• 450 kHz Multiplier Mode• External Vref Input• 2.7V to 5.5V Single-Supply Operation• Extended Temperature Range: -40°C to +125°CApplications:• Set Point or Offset Trimming• Sensor Calibration• Digitally-Controlled Multiplier/Divider• Portable Instrumentation (Battery-Powered)• Motor Feedback Loop Control

The MCP8026 is a 3-phase brushless motor gate driver and power module that integrates the following features: key-off sleep mode, a LIN transceiver, a buck voltage regulator, two LDO regulators, power monitoring comparators, an over-temperature sensor, a zero-crossing detector, a neutral simulator, a comparator and an operational amplifier for motor current monitoring.The phase comparator and multiplexer allow for hardware commutation detection. The neutral simulator allows commutation detection without a neutral tap in the motor. The buck converter is capable of delivering 750 mW of power for powering a companion microcontroller. The buck regulator may be disabled if not used. The on-board 5-V and 12-V low dropout voltage regulators are capable of delivering 30 mA of current.• Integrated operational amplifier• Over-current comparator with DAC reference• Phase comparator with multiplexer• Neutral simulator• Adjustable output buck regulator (750 mW)• Output voltage range: 6 - 19 V• Buck regulator under-voltage lockout: 4.0 V• Under-voltage lockout (UVLO): 5.5 V• Over-voltage lockout (OVLO): 20 V• Transient (100 ms) voltage tolerance: 48 V Technical data:Operating voltage: 6 - 28 VOutput current: 50 mAMotor control: PWM