4006 products were found matching your search for shielded in 1 shops:

Magnetically shielded 10 cm (4”) fullrange speaker with high efficiency, balanced frequency response. Water-repellent cone and rubber gasket. Especially suitable as control speaker in electronic devices and as speaker for public applications and public transport systems.Equivalent to model R 10 SC - 8 Ohm, but with connectors 6.3 x 0.8 mm (+) and 4.8 x 0.8 mm (-) and with impregnated paper gasket.Typical applications Video monitoring screens Control speakers for electronic devices Ceiling-mounted speakers in railway carriages and bussesTechnical DataRated power 20 WMaximum power 30 WNominal impedance Z 8 OhmFrequency response 100-13000 HzMean sound pressure level 90 dB (1 W/1 m)Opening angle (-6 dB) 92°/4000 HzExcursion limit +/-1,5 mmResonance frequency fs 165 Hz

Magnetically shielded 25 mm (1”) high end dome tweeter made of ceramic for crystal clear, perfectly reproduced sound even at high volume settings and with no distortion. The pole piece perforation coupled with the flow-optimised rounded shape, the damping in the cavity and the ventilated voice coil carrier guarantee a very low resonance frequency. The impedance is linearised by means of an integrated LRC element. This means that the dome can be easily integrated in a network of crossovers. The protective grille is fitted on the inside with an acoustic low-pass filter in the shape of a transparent ring, which does not begin to operate until 25 kHz are achieved, when it damps any material-borne resonance. The grille has the added advantage of improving omnidirectional sound distribution at higher frequencies.

AMJ coupling K, Cat. 6A, f-f Suitable for Class EA channel, 10 Gigabit Ethernet Suitable for RJ45/11/12 plugs Cat. 6A in accordance with IEC 60603-7-51Cat. 6A re-embedded, tested in accordance with IEC 60512-27-100Link certification: class EA in accordance with ISO/IEC 1180110-gigabit Ethernet in compliance with IEEE 802.3anContact over-bending protection: = 750 plugging cycles with RJ45/RJ11/RJ12 connectorsSuitable for PoE+ in accordance with IEEE 802.3atWith design-capable carrier module AMJ-S Up/0 flex - can be combined with covers from various switching-program manufacturersIntegrated cable catch for cable diameters of up to 9 mmUniversal, internationally available installation dimensions for 19.3 x 14.7-mm mounting cut-outsVisually monitored inspection of the RJ45 contact heightsAMJ-S DD: with integrated protection against damage to the contacts by automatically releasing the connector

Circular connectorsPlug acc. to IEC 60130-9, IP 68, with threaded joint and solder terminals, shielded at 360°• 5-pole

VALUE RJ-45 coupling, shielded, Cat.6 (Class E), outdoor/industrial, blackCat.6- Coupling for easy connection or extension of patch cables in industrial environments to protect the connection from dust and moistureDustproof cable gland for industrial applicationsProvides protection for the connection against moisture and dirtQuick and easy installation2x shielded RJ45 socketsSuitable for cable diameters up to 3 - 8 mmProtection against moisture only for patch cables with an outer diameter of 6 - 8 mm. Length 136 mmDiameter: 30 mm8 contacts, connected 1:1

Cut optimised for FastConnect connectors - optical length scaling optimised for different connector types - modular pair of blades for ProfibusThe Profibus Stripper No. 2 tool cleanly strips the outer sheath and the shielding underneath to strip the Profibus wire so it can fit its connector. Using the scale in the module for visual length scaling, the correct stripping length can be selected to make Ethernet cables fit FastConnect connectors. The standard stripping lengths of 17 mm, 20 mm, 24 mm and 30 mm are visually marked in the module. The stripper has been developed to cut 5.5 mm to 8 mm Profibus cables with two blade pairs accurately at the same time. The cut profile is perfect for FastConnect connectors - even with different cable diameters. If required, the blade pairs in the half-shells can be changed or replaced.

Round connector with screw cap• Plug in accordance with IEC 60130-9• IP 68• with screw cap• with solder connections• Shielded 360°• 8-pin

unilan® RJ45 module MS-K 1/8 Cat.6a/EA shieldedThe module is specified up to 500 MHz. In conjunction with the Cat.7 or 7A data cable, it is suitablefor all applications of transfer classes D, E and EA, i.e. including 10 GigabitEthernet in accordance with IEEE 802.3an• Compact housing made of die-cast zinc.• Slim design for high packing density (max. 3 modules per data box).• Design of the 2-port version is compatible with switch programs from other manufacturers.• Excellent electrical measurements, suitable for 10 Gigabit Ethernet applications.• Suitable for Power over Ethernet (PoE) in accordance with IEEE 802.3 af.• Cable wires are connected without tools.• 360° shielding braid contact via metal bracket.• Strain relief provided by cable ties.• Mounting in patch panels and data boxes according to special 180° rotated Keystone mounting type.• Solid conductor diameter 0.51mm (AWG24) to 0.63 (AWG22)• Strand conductor diameter depends on the strand design• Can be reconnected. 10 times when using an equivalent or larger cross-section• Outer diameter of wires 0.7. 1.4 mm (1.6 mm)• Storage temperature - 40°C to + 70°C• Processing - 10°C to + 60°C• Operation - 20°C to + 60°C

• For connection/extension of data cables up to Cat.7A• Complies with class E in accordance with ISO/IEC 11801 Ed.2.2:2011-06 in conjunction with Cat.6, Cat.6A, Cat.7 and Cat.7A cables and Cat.6 connection technology• Cable can be fed from one or two sides• Cable-sharing, eight-wire cable can be split into 2 four-wire cables (one cable connector required on input and output side)• Fully shielded metal housing• Strain relief and separate 360º shield connection, captive• Two holes for wall mountingCompact cable connectors for connection or extension of data cables up to Cat.7A.Complies with class E in accordance with ISO/IEC 11801 Ed.2.2:2011-06 in conjunction with Cat.6, Cat.6A, Cat.7 and Cat.7A data cables and Cat.6 connection technology.Fully shielded metal housing in die-cast zinc with four cable feeds, two separate cable clamps for cable strain relief, 360° shield connection and two holes for wall mounting. Split an eight-wired data cable into 2 four-wire data cables (cable sharing). One cable connector requires at the input and output side• Connection technology: IDC connectors• Conductor diameter: AWG 24/1 to AWG 22/1• Cable feed: axial, 2x each left and right• Material: Die-cast zinc

Round connector with screw cap• Plug in accordance with IEC 60130-9• IP 68• with screw cap• with solder connections• Shielded 360°• 4-pin

shiverpeaks®-BASIC-S, Cat. 6 cable connector RJ45, full metal shielded, 5-packConnectors: RJ45 female - RJ45 femaleMaterial housing: ABS shieldedPinning: 1:1 6-8 positions/ 8 contactsContact surface: copper gold platedColor housing: full metal

Cat.6a modular couplers, shielded - 2 piecesCorresponds with requirements channel performance Class EA ISO/IEC 11801 for up to 500 MHzTechnical details2 x RJ-45 femaleAssignment: 1:1Shielded versionMaterial enclosure: Brass sheet - shining Nickel platedMaterial PCB: FR4, 1.2 mm thicknessMaterial contacts: Phosphor bronzeContacts coating: Nickel, gold plated 0.6 µMating cycles: = 750Operating temperature: -10 °C ~+50 °C2 pieces

shiverpeaks®-BASIC-S, Cat. 5 cable connector, RJ45, full metal shielded, 5-packConnectors: RJ45 female - RJ45 maleMaterial housing: ABS shieldedPinning: 1:1, 8 contactsContact surface: copper gold platedColor housing: solid metal

ROLINE RJ-45 coupling, keystone, shielded, Cat.6 (Class E)Feed-through coupling for connection, coupling or extension of RJ-45 network cablesRJ-45 coupling for patching or extending STP twisted pair cablesShielded metal designKeystone designFor installation in standardized cut-outs in patch panels or desktop mountsUniversal, worldwide available installation dimension for mounting cutouts 19.3 x 14.7 mm8 contacts, 1:1 connected

Round connector with screw cap• Coupler in accordance with IEC 60130-9• IP 68• with screw cap• with solder connections• Shielded 360°• 5-pin

LogiLink's pass-through RJ45 connector simplifies cabling by allowing cables to be inserted through the open front of the connector. This speeds up installation and makes it easy to check the correct wiring sequence.RJ45 Cat.6 STP connector, shielded, pass-through (easy plug)Easy-connect: wire pairs are easier to insertSimple check of the pin assignmentSuitable for AWG 24-27 STP cableMax. cable diameter: 4.8 - 6.5 mmMax. insulated wire diameter: 0.97~1.08 mmSet of 50 plugs

shiverpeaks®-BASIC-S, Cat. 6 cable connector RJ45, metallized-shielded, 5-packConnectors: RJ45 female - RJ45 femaleMaterial housing: ABS shieldedPinning: 1:1 6-8 positions/ 8 contactsContact surface: copper gold platedColor housing: metallized

VALUE shielded modular plug, Cat. 5e (Class D), 10 pcsVALUE modular plugShielded modular plugFor use with Cat. 5e cabling

ROLINE Cat.6 (Class E) Keystone, shielded, toolless, silver coloredROLINE Keystone in shielded Cat.6 quality for use in Gigabit Ethernet networksConnection of the cables to the Keystones is done without tools - the cable wires are simply placed in the guides, the module is closed and pressed together - ready is the connectionKeystones with printed color coding according to EIA / TIA 568The Keystone modules can be latched into a 19'' module carrier (26.11.0360 in black or 26.11.0359 in light gray) with ground connection. Or they become a junction box together with a module holder 25.16.8579.The ROLINE Cat.6/Class E 19'' keystones meet the transmission characteristics of a Cat.6/Class E link

LogiLink® socket, CAT6 socket, surface-mounted + flush-mounted, 2x RJ45 STP, signal whiteShielded RJ45 socket, CAT6 with angled outlet and 2 RJ45 ports. Specified up to 250 MHz, this socket is suitable for all data transmissions up to Gigabit Ethernet including PoE and PoE+. The sturdy die-cast zinc housing with combined shield contacting and strain relief is suitable for flush, surface or cable channel mounting. The surface frame is included in delivery. RJ45 socket, category 6, class E, 250 MHzISO/IEC 11801 and ANSI/TIA/EIA 568B.2-12 shielded RJ45 sockets, 40° angleFully shielded housingFlush-mounted and surface-mounted versionColour: RAL9010 whiteSocket angle: 40°Colour coded according to EIA/TIA 568 A&BWith labelling panel