1590 products were found matching your search for solder in 1 shops:

Filled with flux-powder for fine soldering in electronics and electrical engineering Sn100Ni+, EN ISO 9453, 9454 70g Filled with flux-powder for fine soldering in electronics and electrical engineering Sn100Ni+, EN ISO 9453, 9454 70g

For soft soldering of copper pipes in cold and hot water installations Heat resistant up to 110 °C Only use in combination with fittings solder paste CFH no. 52348 or fitting flux-powder CFH no. 52347 S-Sn97Cu3, EN 29453 100 g

Set with the indispensable helpers for delicate work such as solderingsuch asKnife and brushScraper and hookFork and poker

Soldering cross tweezers (holding tweezers) made of steel with fine, smooth, bent tips.smooth gripping surfacesplastic non-slip handleshape R29material quality steelsurface nickel-platedTotal length 160 mmWeight 29 gCorrosion protection due to surface treatment

For gap soldering steels of all kinds, copper and copper alloys For gas and water installations 1 pieces

Composition: 0.3% silver, 0.7% copper, 96.5% tin, flux content: 2.5%, 217°C melting point Environmentally friendly brand solder Improved electrical conductivity due to silver content (0.3%) No cleaning of the solder joints after soldering necessary With continuous flux cores

Composition: 0.3% silver, 0.7% copper, 96.5% tin, flux content: 2.5%, 217°C melting point Environmentally friendly brand solder Improved electrical conductivity due to silver content (0.3%) No cleaning of the solder joints after soldering necessary With continuous flux cores

Miniature clip probe tip with solder connection. Gold-plated phosphorus bronze contact hooks for wires up to 2 mm in diameter. When soldering, remove control button, engage after connecting the cable by pushing until the stop.Colour: redClamping range: max. diameter 2 mmMeasuring category according to IEC 61010: CAT IStandard: IEC 61010Connection type: solderingRated voltage: 30 V AC/60 V DCRated current: 6 AResistance: 15 mOhm

For soldering refined zinc and alloyed zinc in the roofing sector, Sn91Zn9, EN ISO 9453 Use only in combination with zinc sheet soldering fluid CFH no. 52372 2 bars, 295 mm each

This module by Delock can be mounted e.g. in panels or cases with D-type openings for XLR jacks.This makes it ideal for integrating analogue equipment into professional audio systems.Specifications Connectors external: 1 x RCA female > internal: 2 x solder connectionMaterial: zinc die castColour: blackFor D-type ports with 24 x 19 mmPanel cut-out (diameter): ca. 24 mmTwo mounting holes for screw fasteningDimensions (LxWxH): ca. 28.4 x 25.6 x 30.8 mmPackage content D-Type module

Miniature clip probe tip with solder connection. Gold-plated phosphorus bronze contact hooks for wires up to 2 mm in diameter. When soldering, remove control button, engage after connecting the cable by pushing until the stop.Colour: blackClamping range: max. diameter 2 mmMeasuring category according to IEC 61010: CAT IStandard: IEC 61010Connection type: solderingRated voltage: 30 V AC/60 V DCRated current: 6 AResistance: 15 mOhm

ISO-Cream® ''Clear'' lead-free SMD solder paste is a homogeneous, ready-to-use, low-odour mixture of metal powder, binders, solvents and flux powder. It is free of any thixotropic agents, ensuring stable viscosity. This paste has excellent wetting properties and is also great for soldering problematic surfaces such as chem. Ni/Au, chem. AG or OSP. Colourless flux powder residues Low flux spreading First-class wetting on all known surfaces Barely any escape for larger cleaning intervals of the reflow oven Genuine no-clean quality Excellent print quality Long service life of at least 72 hours Perfect soldering results with different soldering profiles Insensitive to environmental influences Retains viscosity even during pressure breaksProduct featuresAlloy: Sn96.5Ag3.0Cu0.5Lead-free: Yes

Solder wire, ''Ultra-Clear'' ISO coreAlloy: Sn96.5/Ag3.0/Cu0.5Flux content: 2.2%Lead-free: YesMelting point: 217 - 219°C

The hot-melting inner adhesive seals watertight with correct overlap - the soldering ring connects the two conductors during the shrinking and melting process! The advantage of the transparent design is that the wrapped object can be seen. The application is very simple: Strip the cable and insert it into the plug on both sides until the stripped cable ends overlap or twist under the soldering ring. Even heating at the melting temperature on the solder until it has melted - preferably with a hot air gun or a hot air blower - finished. The maximum current is limited by the conductor cross-section of the cable used, its conductor material and the quality of the solder joint.

Mini-alligator clips for small components. Clamping range 1 mm² max. Connecting cable cross-section, 0.5 mm² max. for soldering or crimping.• Clamping range: 1 mm• Attachment type: soldering or crimp on• Rated voltage: 60 V DC• Resistance: 15 mO• Colour: bare

Extruded heat sink for mounting on PCB boards34.9 x 12.7 x 38.1 mm, screw-down assemblyWith solder pinsFor TO220, SOT32, TOP3 Profile width: 35 mm Finish: black anodisedSemiconductor mounted using M3 screws (holes without thread) or using transistor retaining clip THF104 (must be ordered separately)

DIY small / SMD clamp test probe with solder connectionColour: redLength: 47 mmHook width: 1 mmRated voltage: 30 V AC/60 V DCCurrent rating: 6 AContact: gold-plated brassApplication: For self-assembly of mini-hook clamp connections.The hook fits 1.2 mm diameter round pins and 0.9 mm x 0.9 mm square pins. The gold plating prevents oxidation and ensures good electrical conductivity.

This module by Delock can be mounted e.g. in panels or cases with D-type openings for XLR jacks.This makes it ideal for integrating analogue equipment into professional audio systems.Specifications Connectors external: 1 x BNC female > internal: 2 x solder connectionMaterial: zinc die castColour: blackFor D-type ports with 24 x 19 mmPanel cut-out (diameter): ca. 24 mmTwo mounting holes for screw fasteningDimensions (LxWxH): ca. 31.4 x 26.0 x 31.0 mmPackage content D-Type module

This module by Delock can be mounted e.g. in panels or cases with D-type openings for XLR jacks.This makes it ideal for integrating digital equipment into professional audio systems.Specification Connectors: external: 1 x RJ45 jack internal: 1 x solder connectionMaterial: zinc die castColour: blackFor D-type ports with 25 x 25 mmPanel cut-out (diameter): ca. 21 mmTwo mounting holes for screw fasteningDimensions (LxWxH): ca. 25 x 25 x 25 mmPackage content D-Type modulePackage Zip poly bag

For removing solder residues when de-soldering electronic components The white soldering tip consists of Teflon material The housing consists of aluminium (black) and PA6 polymer (blue)