1257 products were found matching your search for transistor in 1 shops:

Tweezers for SMD/THT technology for gripping round, cubic, cylindrical components and parts, mini MELFs, diodes, resistors.Also suitable for inserting and pulling various plug-in transistors through bulbous or long-hollow receptacle.straight, right-angled insulated gripping jaws 5 mmnon-slipshape 64Material quality steelsurface nickel-platedtotal length 145 mmWeight 23 gSteel (nickel-plated) with PVC-insulated curved gripping jaws

Trans Darlington NPN 30V 0.3A 300mW 3-Pin SOT-23 T/

Reliable power transistorEnclosure: TO-220

36-V power transistorDescription:The LP395 is a fast monolithic transistor with complete overload protection. This very high gain transistor has included on the chip, current limiting, power limiting, and thermal overload protection, making it difficult to destroy from almost any type of overload. Available in an epoxy TO-92 transistor package this device is specified to deliver 100 mA. Thermal limiting at the chip level, a feature not available in discrete designs, provides comprehensive protection against overload. Excessive power dissipation or inadequate heat sinking causes the thermal limiting circuitry to turn off the device preventing excessive die temperature. The LP395 offers a significant increase in reliability while simplifying protection circuitry. It is especially attractive as a small incandescent lamp or solenoid driver because of its low drive requirements and blowout-proof design. The LP395 is easy to use and only a few precautions need be observed. Excessive collector to emitter voltage can destroy the LP395 as with any transistor. When the device is used as an emitter follower with a low source impedance, it is necessary to insert a 4.7 kO resistor in series with the base lead to prevent possible emitter follower oscillations. Also since it has good high frequency response, supply by-passing is recommended. Areas where the LP395 differs from a standard NPN transistor are in saturation voltage, leakage (quiescent) current and in base current. Since the internal protection circuitry requires voltage and current to function, the minimum voltage across the device in the on condition (saturated) is typically 1.6 Volts, while in the off condition the quiescent (leakage) current is typically 200 µA. Base current in this device flows out of the base lead, rather than into the base as is the case with conventional NPN transistors. Also the base can be driven positive up to 36 Volts without damage, but will draw current if driven negative more than 0.6 Volts. Additionally, if the base lead is left open, the LP395 will turn on. The LP395 is a low-power version of the 1-Amp LM195/LM295/LM395 Ultra Reliable Power Transistor. The LP395 is rated for operation over a -40°C to +125°C range.Features:• Internal Thermal Limiting• Internal Current and Power Limiting• Specified 100 mA Output Current• 0.5 µA Typical Base Current• Directly Interfaces with TTL or CMOS• +36 Volts On Base Causes No Damage• 2 µs Switching Time

Features• designed for Complementary Use with TIP130, TIP131 and TIP132• 70 W at 25°C Case Temperature• 8 A Continuous Collector Current• minimum hFE of 1000 at 4 V, 4 A

Housing: TO-3PN

2SA 1381

Features:• Max. power dissipation with cooling: 65W• Collector current: 5A• Plastic case: TO-220AB• Weight approx.: 2.2 g• Plastic material has UL classification 94V-0• Standard packaging in tubes

Description• with TO-220C package• DARLINGTON • collector saturation voltage • complement to type TIP135/136/137 Applications• designed for general-purpose amplifier and low speed switching applications

Description• with TO-3 package • DARLINGTON• high DC current gain • complement to type MJ3000/3001Applications• for use as output devices in complementary general purpose amplifier applications

Transistor PNP-Darl TO-3PFA 120 V, 50 A, 300 W

Description• with TO-3PN package • DARLINGTON • 10A rated continuous collector currentApplications• for use in automotive ignition, switching and motor control applications

Transistor 2SC 3503 NPN, 300 V, 0.1 A, TO-126

Features• Max. power dissipation with cooling: 65W• Collector current: 5A• Plastic case: TO-220AB• weight approx.: 2.2 g• Plastic material has UL classification 94V-0• Standard packaging in tubes

The TIP142 is an Epitaxial-base NPN power transistor in monolithic Darlington configuration, mounted in TO-247 plastic package. It is intended for use in power linear and switching applications. The PNP complementary type is TIP147.Features• monolithic Darlington configuration• integrated antiparallel collector-emitter diodeApplications• linear and switching industrial equipment

Housing: TO-220= BDX 34D

Description• with TO-220C package • DARLINGTON• high DC current gain• low collector saturation voltage• complement to type TIP125/126/127Applications • designed for general–purpose amplifier and low–speed switching applications.

TIP125 ... TIP127• Max. power dissipation with cooling: 65W• Collector current: 5A• Plastic case: TO-220AB• Weight approx.: 2.2 g• Plastic material has UL classification 94V-0• Standard packaging in tubes